ASRock 970 Extreme3 manual Chassis Speaker Header

Page 28

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header

Please connect the chassis

(4-pin SPEAKER 1)

speaker to this header.

(see p.12 No. 24)

 

Power LED Header

(3-pin PLED1)

1

 

 

 

 

 

 

 

 

 

 

 

 

PLED-

(see p.12 No. 22)

 

 

 

PLED+

 

 

 

PLED+

Please connect the chassis power LED to this header to indicate system power status. The LED is on when the system is operating. The LED keeps blinking in S1 state. The LED is off in S3/S4 state or S5 state (power off).

Chassis and Power Fan Connectors

(4-pin CHA_FAN1)

(see p.12 No. 12)

(3-pin CHA_FAN2)

GND

(see p.12

No. 15)

+12V

CHA_FAN_SPEED

(3-pin CHA_FAN3)

 

(see p.12

No. 2)

 

(3-pin PWR_FAN1)

GND

+12V

(see p.12

No. 10)

PWR_FAN_SPEED

Please connect the fan cables to the fan connectors and match the black wire to the ground pin. CHA_FAN1/2/3 fan speed can be controlled through UEFI or AXTU.

28

Image 28
Contents Extreme3 Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector Bios FeatureRear Panel I/O USBUnique Feature HardwareMonitor CertificationsPage Page Page Motherboard Layout 21.8cm 8.6-inLAN Port LED Indications I/O PanelTable for Audio Output Connection Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Expansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots CrossFireXTM and Quad CrossFireXTM Operation Guide CrossFire Bridge For Windows XP OS Driver Installation and SetupFor Windows 7 / VistaTM OS Surround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide CIR sensors in different anglesJumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsConsumer Infrared Module Header Chassis Speaker Header Supply to this connector ATX 12V Power ConnectorHdmispdif Header Hdmispdif header, providing Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Installing Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi Use RAID Installation Guide to set RAID configuration \ RAID Installation GuideInstalling Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Uefi Menu Bar Navigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen Dram Configuration Dram Frequency AMD Turbo Core TechnologyAMD IO C-State Support Processor Maximum FrequencyPower Down Enable RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWRWould you like to save current setting user defaults? Four Activate Window tFAWVoltage Control Dram Voltage NB VoltageAdvanced Screen Instant FlashCPU Configuration Cool ‘n’ QuietSecure Virtual Machine Enhance Halt State C1ENorth Bridge Configuration Primary Graphics AdapterSouth Bridge Configuration Storage Configuration Sata ModeSata IDE Combined Mode Sata ControllerSuper IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration Acpi Hpet table USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportCPU Fan 1 & 2 Setting Chassis Fan 1 SettingChassis Fan 2 Setting Chassis Fan 3 SettingBoot Screen Security Screen Exit Screen Install Operating System Support CD InformationRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Drv4E CtrlB5 LangengChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 7 64-bit