ASRock A75 Pro4-M manual ASRock Smart Remote Installation Guide, CIR sensors in different angles

Page 29

2.8 ASRock Smart Remote Installation Guide

ASRock Smart Remote is only used for ASRock motherboard with CIR header. Please refer to below procedures for the quick installation and usage of ASRock Smart Remote.

Step1. Find the CIR header located next to the USB 2.0 header on ASRock motherboard.

Step2. Connect the front USB cable to the USB 2.0 header (as below, pin 1-5) and the CIR header. Please make sure the wire assignments and the pin assignments are matched correctly.

USB 2.0 header (9-pin, blue)

CIR header (4-pin, white)

USB_PWR

P-

P+

GND DUMMY

GND

IRTX

IRRX

ATX+5VSB

Step3. Install Multi-Angle CIR Receiver to the front USB port. If Multi-Angle CIR Receiver cannot successfully receive the infrared signals from MCE Remote Controller, please try to install it to the other front USB port.

3 CIR sensors in different angles

1.Only one of the front USB port can support CIR function. When the CIR function is enabled, the other port will remain USB function.

2.Multi-Angle CIR Receiver is used for front USB only. Please do not use the rear USB bracket to connect it on the rear panel. Multi-Angle CIR Receiver can receive the multi-direction infrared signals (top, down and front), which is compatible with most of the chassis on the market.

3.The Multi-Angle CIR Receiver does not support Hot-Plug function. Please install it before you boot the system.

* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://www.asrock.com

29

Image 29
Contents A75 Pro4-M Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Audio ConnectorRear Panel I/O USBUnique Feature Bios FeatureSupport CD HardwarePage Page Page Dual Motherboard LayoutTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Pre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmInstalling a Dimm Pcie Slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots CrossFireXTM and Quad CrossFireXTM Operation Guide Graphics Card SetupCrossFire Bridge For Windows 7 / VistaTM OS Driver Installation and SetupFor Windows XP OS Page What does an AMD Dual Graphics system include? AMD Dual Graphics Operation GuideEnjoy the benefit of AMD Dual Graphics AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureHdcp Function What is HDCP?For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS CIR sensors in different angles ASRock Smart Remote Installation GuideDescription Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsInfrared Module Header Chassis Speaker Header ATX 12V Power Connector CPU Fan ConnectorsSerial port Header What is Hot Plug Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Set up Uefi Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Main Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen RAS# to CAS# Delay tRCD Dram Timing Control Power Down EnableCommand Rate CR Write Recovery Time tWRWrite to Read Delay tWTR RAS to RAS Delay tRRDWould you like to save current setting user defaults? Refresh Cyle Time tRFCInstant Flash Advanced ScreenCore C6 Mode CPU ConfigurationPackage C6 Mode Cool ‘n’ QuietNorth Bridge Configuration South Bridge Configuration Sata Mode Storage ConfigurationSata IDE Combined Mode Sata ControllerSuper IO Configuration Acpi Configuration Acpi Hpet table USB 2.0 Controller USB ConfigurationUSB 3.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen CPU Fan 1 & 2 SettingChassis Fan 1 Setting Boot Screen Security Screen Exit Screen Support CD Information Install Operating SystemRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 260 pages 9.73 Kb