ASRock A75 Pro4-M manual Infrared Module Header

Page 32

Infrared Module Header

+5VSB

 

IRTX

(5-pin IR1)

DUMMY

 

(see p.12 No. 26)

1

 

GND

 

IRRX

This header supports an optional wireless transmitting and receiving infrared module.

Consumer Infrared Module Header

This header can be used to

(4-pin CIR1)

connect the remote

(see p.12 No. 23)

controller receiver.

Front Panel Audio Header

 

 

 

 

PRESENCE#

 

 

 

GND

(9-pin HD_AUDIO1)

 

 

 

 

 

 

MIC_RET

 

 

 

 

 

 

 

 

 

 

OUT_RET

(see p.12 No. 30)

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT2_L

 

 

 

 

 

 

 

 

J_SENSE

 

 

 

 

 

 

 

OUT2_R

 

 

 

 

 

MIC2_R

 

 

 

MIC2_L

This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.12 No. 17)

functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con- figure the way to turn off your system using the power switch.

32

Image 32
Contents A75 Pro4-M Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector AudioRear Panel I/O USBBios Feature Unique FeatureSupport CD HardwarePage Page Page Motherboard Layout DualTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Pcie Slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots Graphics Card Setup CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge For Windows 7 / VistaTM OS Driver Installation and SetupFor Windows XP OS Page What does an AMD Dual Graphics system include? AMD Dual Graphics Operation GuideEnjoy the benefit of AMD Dual Graphics AMD Vision Engine Control Center Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature For Windows XP / XP 64-bit OSHdcp Function What is HDCP?For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS ASRock Smart Remote Installation Guide CIR sensors in different anglesJumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsInfrared Module Header Chassis Speaker Header CPU Fan Connectors ATX 12V Power ConnectorSerial port Header Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Set up Uefi Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Use RAID Installation Guide to set RAID configuration \ RAID Installation Guide Make a SATA3 Driver DisketteInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Navigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen Dram Timing Control Power Down Enable RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWRRAS to RAS Delay tRRD Write to Read Delay tWTRWould you like to save current setting user defaults? Refresh Cyle Time tRFCAdvanced Screen Instant FlashCPU Configuration Core C6 ModePackage C6 Mode Cool ‘n’ QuietNorth Bridge Configuration South Bridge Configuration Storage Configuration Sata ModeSata IDE Combined Mode Sata ControllerSuper IO Configuration Acpi Configuration Acpi Hpet table USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen CPU Fan 1 & 2 SettingChassis Fan 1 Setting Boot Screen Security Screen Exit Screen Install Operating System Support CD InformationRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 260 pages 9.73 Kb