ASRock A75M-HVS manual Dual Monitor and Surround Display Features, Dual Monitor Feature

Page 19

2.6 Dual Monitor and Surround Display Features

Dual Monitor Feature

This motherboard supports dual monitor feature. With the internal VGA output sup- port (D-Sub and HDMI), you can easily enjoy the benefits of dual monitor feature without installing any add-on VGA card to this motherboard. This motherboard also provides independent display controllers for D-Sub and HDMI to support dual VGA output so that D-sub and HDMI can drive same or different display contents.

To enable dual monitor feature, please follow the below steps:

1.Connect D-Sub monitor cable to D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel.

VGA/D-Sub port HDMI port

2.If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefits of dual monitor function after your system boots. If you haven’t installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer.

19

Image 19
Contents A75M-HVS Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Rear Panel I/O ConnectorBios Feature Unique FeatureMonitor HardwareCertifications Page Page 2400+ Motherboard LayoutLAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots Enjoy the benefit of AMD Dual Graphics AMD Dual Graphics Operation GuideWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureFor Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS What is HDCP?Hdcp Function CIR sensors in different angles ASRock Smart Remote Installation GuideDescription Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsInfrared Module Header Pled System Power LED CPU Fan ConnectorsPlease connect an ATX 12V power supply to this connector ATX 12V Power ConnectorHot Plug and Hot Swap Functions for SATA3 HDDs Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Installing Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar System Time HourMinuteSecond Navigation KeysMain Screen To jump to the Exit Screen or exit the current screenOC Tweaker Screen Write Recovery Time tWR Dram Timing Control Power Down EnableRAS# to CAS# Delay tRCD Command Rate CRRefresh Cyle Time tRFC RAS to RAS Delay tRRDWrite to Read Delay tWTR Would you like to save current setting user defaults?Instant Flash Advanced ScreenCool ‘n’ Quiet CPU ConfigurationCore C6 Mode Package C6 ModeOnboard Hdmi HD Audio North Bridge ConfigurationPrimary Graphics Adapter Share MemoryOnboard LAN South Bridge ConfigurationOnboard HD Audio Front PanelSata Controller Storage ConfigurationSata Mode Sata IDE Combined ModeSuper IO Configuration Acpi Configuration Acpi Hpet table Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerChassis Fan 1 Setting CPU Fan 1 SettingHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Drivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 232 pages 32.74 Kb