ASRock A75iCafe manual CIR sensors in different angles

Page 28

3 CIR sensors in different angles

1.Only one of the front USB port can support CIR function. When the CIR function is enabled, the other port will remain USB function.

2.Multi-Angle CIR Receiver is used for front USB only. Please do not use the rear USB bracket to connect it on the rear panel. Multi-Angle CIR Receiver can receive the multi-direction infrared signals (top, down and front), which is compatible with most of the chassis on the market.

3.The Multi-Angle CIR Receiver does not support Hot-Plug function. Please install it before you boot the system.

* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://www.asrock.com

28

Image 28
Contents A75iCafe Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector Bios FeatureUnique Feature Rear Panel I/OMonitor HardwareCertifications Page Page Page Motherboard Layout I/O Panel LAN Port LED IndicationsInstallation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots Graphics Card Setup CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge For Windows XP OS Driver Installation and SetupFor Windows 7 / VistaTM OS Page Enjoy the benefit of AMD Dual Graphics AMD Dual Graphics Operation GuideWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature For Windows XP / XP 64-bit OSFor Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS What is HDCP?Hdcp Function ASRock Smart Remote Installation Guide Advanced Super IO Configuration CIR Controller EnabledCIR sensors in different angles Jumpers Setup DescriptionOnboard Headers and Connectors Serial ATA2 ConnectorsUSB 3.0 Header System Panel Header CPU Fan Connectors ATX 12V Power ConnectorSerial port Header Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Installing Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi Use RAID Installation Guide to set RAID configuration \ RAID Installation Guide Make a SATA3 Driver DisketteInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Navigation Keys Main ScreenNavigation Keys + / Tab Enter Pgup Pgdn Home F10 F12OC Tweaker Screen Dram Configuration Dram Frequency Dram Timing Control Power Down EnableRAS# to CAS# Delay tRCD CPU VoltageCommand Rate CR Write Recovery Time tWRRAS to RAS Delay tRRD Write to Read Delay tWTRWould you like to save current setting user defaults? SB VoltageAdvanced Screen Instant FlashCPU Configuration Core C6 ModeCstate Pmin Mode Cool ‘n’ QuietNorth Bridge Configuration Primary Graphics AdapterShare Memory Onboard Hdmi HD AudioSouth Bridge Configuration Onboard HD AudioFront Panel Onboard LANStorage Configuration Sata ModeSata IDE Combined Mode Sata ControllerSuper IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration Acpi Hpet table USB Configuration USB 2.0 ControllerLegacy USB Support Legacy USB 3.0 SupportCPU Fan 1 Setting Chassis Fan 1 SettingChassis Fan 2 Setting Hardware Health Event Monitoring ScreenBoot Screen Security Screen Load Uefi Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Drv4E CtrlB5 LangengChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 7 64-bit