ASRock A75iCafe manual

Page 67

B. Disable “Volume Shadow Copy” service.

a. Type “computer management” in the Start Menu, then press “Enter”.

b. Go to “Services and Applications>Services”; Then double click “Volume Shadow Copy”.

c. Set “Startup type” to “Disable” then Click “OK”.

67

Image 67

Contents A75iCafe Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Rear Panel I/O ConnectorBios Feature Unique FeatureMonitor HardwareCertifications Page Page Page Motherboard Layout LAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots CrossFireXTM and Quad CrossFireXTM Operation Guide Graphics Card SetupCrossFire Bridge For Windows XP OS Driver Installation and SetupFor Windows 7 / VistaTM OS Page Enjoy the benefit of AMD Dual Graphics AMD Dual Graphics Operation GuideWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureFor Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS What is HDCP?Hdcp Function Advanced Super IO Configuration CIR Controller Enabled ASRock Smart Remote Installation GuideCIR sensors in different angles Description Jumpers SetupSerial ATA2 Connectors Onboard Headers and ConnectorsUSB 3.0 Header System Panel Header ATX 12V Power Connector CPU Fan ConnectorsSerial port Header Hot Plug and Hot Swap Functions for SATA3 HDDs Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Installing Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar F10 F12 Navigation KeysMain Screen Navigation Keys + / Tab Enter Pgup Pgdn HomeOC Tweaker Screen CPU Voltage Dram Configuration Dram FrequencyDram Timing Control Power Down Enable RAS# to CAS# Delay tRCDWrite to Read Delay tWTR Command Rate CRWrite Recovery Time tWR RAS to RAS Delay tRRDSB Voltage Would you like to save current setting user defaults?Instant Flash Advanced ScreenCool ‘n’ Quiet CPU ConfigurationCore C6 Mode Cstate Pmin ModeOnboard Hdmi HD Audio North Bridge ConfigurationPrimary Graphics Adapter Share MemoryOnboard LAN South Bridge ConfigurationOnboard HD Audio Front PanelSata Controller Storage ConfigurationSata Mode Sata IDE Combined ModeInfrared Port Super IO ConfigurationSerial Port Serial Port AddressAcpi Configuration Acpi Hpet table Legacy USB 3.0 Support USB ConfigurationUSB 2.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen CPU Fan 1 SettingChassis Fan 1 Setting Chassis Fan 2 SettingBoot Screen Security Screen Discard Changes and Exit Load Uefi DefaultsExit Screen Save Changes and ExitDrivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB in Ahci Mode Drv4E CtrlB5 Langeng Installing OS on a HDD Larger Than 2TB in RAID ModeChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 7 64-bit