Carvin LC24 manual File Dump Connections Open Loop Mode, Closed Loop Mode, Midi OUT Settings

This symbol is intended to alert the user		This symbol is intended to alert the
	CAUTION
to the presence of uninsulated “dangerous		user to the presence of important
voltage” within the product’s enclosure that		operating and maintenance (servic-
may be of sufficient magnitude to consti-	RISK OF ELECTRIC SHOCK	ing) instructions in the literature
tute a risk of electric shock to persons.	DO NOT OPEN	accompanying the appliance.

IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polariza- tion means of an appliance is not defeated.

POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

SERVICING: The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to replacement text on the unit for correct fuse type.

SAFETY INSTRUCTIONS (EUROPEAN)

The conductors in the AC power cord are colored in accordance with the following code.

GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live

U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is unsafe. NEVER

UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET.

LIMITED WARRANTY

Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn drivers or speakers dam- aged by this unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or implied. No representative or person is authorized to represent or assume for Carvin any liability in connec- tion with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDEN-

TAL OR CONSEQUENTIAL DAMAGES.

When RETURNING merchandise to the factory, you may call for a return authorization number. Describe in writing each problem. If your unit is out of warranty, you will be charged the cur- rent FLAT RATE for parts and labor to bring your unit up to factory specifications.

MAINTAINING YOUR EQUIPMENT

Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit can be wiped from time to time with a dry or slightly damp cloth in order to remove dust and bring back the new look. As with all pro gear, avoid prolonged use in caustic environments (salt air). When used in such an environment, be sure the mixer is ade- quately protected by a cover.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!

MIDI IN SETTINGS

1.) Press and hold RECORD

2.) Press 1st FLASH KEY 3 times, then release RECORD. When CHI appears on display you can select MIDI IN channels from the 1ST FLASH to the 16TH FLASH.

3.) After you press the desired FLASH, the appropriate channel LED is lit.

4.) Press RECORD and EXIT to withdraw MIDI IN settings.

A. MIDI OUT SETTINGS

1.) Press and hold RECORD

2.) Press 2nd FLASH KEY 3 times, then release RECORD. When CHO appears on the display you can select MIDI IN channels from the 1ST FLASH to the 16TH FLASH.

3.) After you press the desired FLASH, the appropriate channel LED is lit.

4.) Press RECORD and EXIT to withdraw MIDI OUT settings.

B. RECEIVE FILE DUMP 1.) Press and hold RECORD

2.) Press 3rd FLASH KEY 3 times, then release RECORD. When IN appears on display it is ready to receive file dump.

3.) All other operation are void when receiving file dump. The LC24 will automatically cease transfer when com- plete. A file dump will cease if an error occurs during transfer or if the power is interrupted.

C. SEND FILE DUMP

1.) Press and hold RECORD

2.) Press 4th FLASH KEY 3 times, then release RECORD. When OUT appears on display it is ready to send file dump.

3.) All other operation are void when receiving file dump. The LC24 will automatically cease transfer when com- plete. A file dump will cease if an error occurs during transfer or if the power is interrupted.

D. FILE DUMP CONNECTIONS

OPEN LOOP MODE

TRANSMITTER	RECEIVER
MIDI OUT MIDI IN	MIDI OUT MIDI IN

CLOSED LOOP MODE

TRANSMITTER	RECEIVER
MIDI OUT MIDI IN	MIDI OUT MIDI IN

NOTE:

When sending file dump with an OPEN LOOP MODE, you should set up the receiving device to RECEIVING MODE or receiving will be disabled.

1.If MIDI data is not received within 10 minutes, the channel and program set too MIDI will be cleared.

2.When sending or receiving a file dump, the device ID is 55H. All information is sent or received during a file dump. You can send SCENE programs to an external storage or to another unit. You can also receive SCENE programs from external storage or from another unit. This unit sends or receives NOTE information , relevant functions is as follows:

NOTE NUMBER		VELOCITY	FUNCTION
22-69	PROGRAM MASTER		ON-OFF PROGRAM 1-48
70-93	CHANNEL DIMMER		ON-OFF PROGRAM 1-24
94			FULL ON
95			DARK
96			HOLD
97			TURN ON /OFF AUDIO CHASE
98			CHASE SCENES
99			DOUBLE PRESET MODE
100			SINGLE PRESET MODE
101			STEP CHANGE
102			BLACK OUT

	LC24 SPECIFICATIONS:
Power input:	DC12v-18V 500mA.
DMX output:	3pin XLR
MIDI output:	5 pin DIN
Audio Mic :	internal
Audio input:	RCA jack
Remote input:	stereo 1/4"
Internal fuse:	0.5A 250V 5x20mm
Dimensions:	19x10.4x3.4 inch.
AC adapter:	120VAC – 12VDC 500mA
Weight:	10.6 lbs

RECEIVING INSPECTION—read before getting started INSPECT YOUR MIXER FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company and CARVIN immediately.

SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit, always use the original carton and packing material. This will provide the best pos- sible protection during shipment. CARVIN and the shipping company are not liable for any damage caused by improper packing.

SAVE YOUR INVOICE. It will be required for warranty ser- vice if needed in the future.

SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring.

RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for your records. Keep your portion of the card and return the portion with your name and comments to us.

For your records, you may wish to record the following information.

Serial No.________________________________ Invoice Date_______________