Lochinvar SDT/SET065 - 119 operation manual Install tank sensor, Connect tank sensor

Page 18

SDT/SET Installation & Operation Manual

5Wiring

Indirect Water Heater Sensor Setup (Knight Boiler)

￿CAUTION

NOTICE

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

The sensor supplied contains an Auto Reset High Limit (194°F).

Install tank sensor

The tank sensor is a dual sensor which controls the temperature of the tank from the boiler(see FIG. 5-3). The tank sensor has a built-in high temperature limit set at 194°F.

1.Install the sensor inside the tank as depicted in FIG. 5-3.

2.Connect the wire leads to the DHW Tank Sensor (AUX) connection point on the Knight boiler connection board (see FIG. 5-3).

3.The Knight boiler will automatically read the sensor and default the tank temperature setting to 125°F.

4.Adjust the tank set point program. Reference the Knight Installation and Operation Manual for a detailed explanation of the tank set point program.

Connect tank sensor

1.Turn OFF the power to the unit. Use wire strippers to strip one inch of insulation from the ends of each wire that will be spliced.

2.Splice the two ends of bare wire by twisting them together with a pair of electrical pliers. Turn the pliers three or four times to make a sufficient connection.

3.Attach a wire nut at the point where the two wires have been twisted together. Twist the wire nut until it fits snugly, or until it cannot be twisted any more.

4.Wrap the wire nut and the two wires with electrical tape to secure the connection. Cover any exposed wiring with electrical tape.

Figure 5-3Indirect Water Heater Controlled Using Tank Sensor

TANK BULBWELL

DHW TANK

SENSOR

KNIGHT LOW VOLTAGE

DHW TANK SENSOR / AUTO RESET HIGH LIMIT TERMINAL STRIP (PLACE SENSOR IN TANK BULBWELL & SNAP

CLIP OVER BULBWELL)

SOLAR SENSOR

(FIELD SUPPLIED)

KNIGHT BOILER

INDIRECT TANK

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation & Operation Manual Solar Dual Coil TankSave this manual for future reference Contents When servicing the indirect water heater Please read before proceedingGeneral Information Component MaterialPre-installation Characteristic Min MaxMinimum Clearance to the Element Cover Multiple Tank Connections Boiler Side Boiler Side Piping SDT modelsZone with Circulator to Aquastat Zone with Valve to AquastatSDT / SET119 Friction Loss Pressure Drop ValuesZone #1 2Piping Diagram Zoned with Valves 3Knight Boiler Primary / Secondary Piping 4Multiple Tank Connections Domestic Water Piping for Distant Fixtures Domestic Side Tank PipingBasic Domestic Piping Multiple Tank Domestic Water PipingInstall Drain Valve 1Drain Valve InstalledRelief Valve Discharge Piping 2Recommended Domestic Water Piping SDT/SET models Electrical Connection WiringThermostat Adjustment Combination Thermostat and High Limit Control ECOSET Wiring Single Element Model Volts / Phase Watts / Amps Breaker Type Wire GageInstall tank sensor Connect tank sensor4Wiring for Zone Control Start-up and Check-out Maintenance Maintenance SchedulePerformance Data Boiler 180200 High Output Piping Series PipingParallel Piping Parallel Configuration Friction Loss SDT Series

SDT/SET065 - 119 specifications

The Lochinvar SDT/SET065 - 119 is a sophisticated heating solution that combines efficiency, reliability, and innovative technology to meet the demands of modern residential and commercial applications. As a participant in the highly competitive heating market, Lochinvar has established a reputation for producing high-quality products, and the SDT/SET065 - 119 is no exception.

One of the main features of the Lochinvar SDT/SET065 - 119 is its high-efficiency operation. With an impressive thermal efficiency rating, this unit minimizes energy consumption while maximizing output. This efficiency not only helps in reducing utility bills for users but also contributes to a more sustainable environment by lowering carbon emissions. The design of the unit incorporates advanced heat exchanger technology that optimizes thermal transfer, ensuring that homeowners and businesses receive the precise heating they require.

The SDT/SET065 - 119 also boasts impressive versatility. It can be configured to work with various hydronic heating systems, making it suitable for a wide range of applications, from radiant floor heating to baseboard heating systems. Additionally, the compact design of the unit allows for easy installation and integration into existing systems, without requiring significant modifications.

User-friendly controls are another highlight of the Lochinvar SDT/SET065 - 119. The unit features advanced digital control technology that allows for easy temperature regulation and monitoring. This technology also enables users to take advantage of multiple operating modes, enhancing both comfort and efficiency. Furthermore, built-in diagnostic capabilities provide real-time feedback on the system’s performance, facilitating easier troubleshooting and maintenance.

Safety is also a key consideration in the design of the SDT/SET065 - 119. The unit includes multiple safety features, such as over-temperature protection and pressure relief systems, ensuring reliable operation without compromising user safety.

In summary, the Lochinvar SDT/SET065 - 119 exemplifies modern heating technology. Its high efficiency, versatility, user-friendly controls, and robust safety features make it an ideal choice for those seeking a reliable and effective heating solution. Whether for residential or commercial use, the Lochinvar SDT/SET065 - 119 stands out as a top-tier option in the heating market.
Top Page Image Contents