ASRock Fatal1ty X79 Champion manual Driver Installation Guide, Set up Uefi

Page 67

2.22 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from top to bottom to install those required drivers. Therefore, the drivers you install can work properly.

2.23Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit With RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATA2 / SATA3 HDDs with RAID functions, please follow the steps below.

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Configuration. B. Set the option “SATA Mode” to [RAID] for Intel® SATA2 / SATA3 ports.

Set the option “Bootable Marvell SATA3 Controller“ to [Yes] for Marvell SATA ports.

STEP 2: Use “RAID Installation Guide” to set RAID configuration.

Before you start to configure the RAID function, you need to check the installation guide in the Support CD for proper configuration. Please refer to the document in the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”, which is located in the folder at the following path:

.. \ RAID Installation Guide

STEP 3: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

After the installation of Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS, if you want to manage RAID functions, you are allowed to use both “RAID Installation Guide” and “Intel Rapid Storage Information” for RAID configuration. Please refer to the document in the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”, which is lo- cated in the folder at the following path: .. \ RAID Installation Guide and the document in the support CD, “Guide to Intel Rapid Storage”, which is located in the folder at the follow- ing path: .. \ Intel Rapid Storage Information

If you want to make the USB flash driver disk, please copy above Intel® RAID drivers from our Support CD to your USB flash, and then load drivers from the USB flash disk.

67

Image 67

Contents Fatal1ty X79 Champion Series Fatal1ty Story LIVIN’ Large Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Rear Panel I/O ConnectorUSB3.0 Hardware Bios FeatureUnique Feature Support CDFCC, CE, Whql CertificationsPage Page Page Motherboard Layout LAN Port LED Indications I/O PanelTable for Audio Output Connection Screw Holes Pre-installation PrecautionsCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a Dimm Expansion Slots PCI and PCI Express Slots Pcie Slot ConfigurationsInstalling an expansion card ASRock Game Blaster Configuration CrystalVoice Select a recording device Mic VolumeAcoustic Echo Cancellation Mic BoostHot Key Configuration Scout ModeRear pair Speakers / Headphones ConfigurationOptional Speakers Center SubwooferMixer Equalizer Device Connected Play stereo mix to digital output User Profiles ProfilePage Requirements Two Goldfingers Installing Three SLITM-Ready Graphics CardsASRock 3-Way SLI Bridge Card Installing Four SLITM-Ready Graphics Cards Select Nvidia Control Panel tab Driver Installation and SetupFollow steps a to E on Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards Installing Four CrossFireXTM-Ready Graphics Cards For Windows 7 / VistaTM OS \ Surround Display Information Surround Display FeatureAdvanced Super IO Configuration CIR Controller Enabled ASRock Smart Remote Installation GuideCIR sensors in different angles Description Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsUSB 2.0 Headers Besides two default USB Consumer Infrared Module Header This header can be used to Chassis Speaker Header Please connect the chassis Ground pin ATX Power ConnectorPort on the I/O panel, there Hdmispdif Header Hdmispdif header, providing Installation Guide of Rear USB 3.0 Bracket Installation Guide of Front USB 3.0 PanelSmart Switches Status Code Description 15 Dr. DebugPage Page Post Status Checker PSC Serial ATA3 SATA3 Hard Disks Installation Serial ATA Sata / Serial ATA2 SATA2 Hard Disks InstallationHot Plug and Hot Swap for SATA3 HDDs What is Hot Plug?What is Hot Swap? Hot Plug and Hot Swap for Sata / SATA2 HDDsSata / SATA2 / SATA3 HDD Hot Plug and Operation Guide Sata power cableHow to Hot Plug a Sata / SATA2 / SATA3 HDD Set up Uefi Driver Installation GuideUse RAID Installation Guide to set RAID configuration Page Untied Overclocking Technology Uefi Menu Bar IntroductionMain Screen Navigation KeysOC Tweaker Screen Core Current Limit Turbo Boost Power LimitDram Timing Configuration Load XMP Setting Dram Configuration Dram tCLDram tRAS Command RateDram Power Down Mode Dram tRPRank Interleaving Memory Power Savings ModeMemory Mode Channel InterleavingDram tWWDD Dram Fine Tuning SPDram Fine Tuning SN Voltage Configuration CPU Core VoltageDram Channel A/B DQ Load Power Saving ModeUser Defaults Dram Channel A/B CAInstant Flash Advanced ScreenInternet Flash CPU Configuration CPU C6 State Support CPU Thermal ThrottlingEnhance Halt State C1E CPU C3 State SupportCore Current Limit North Bridge Configuration South Bridge Configuration Onboard Debug Port LED Storage Configuration Marvell 9230 RAID Configuration Marvell 9230 SATA3M0M1M2M3 Operation ModeInfrared Port Super IO ConfigurationSerial Port Serial Port AddressAcpi Configuration Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerME Subsystem Intel ME Subsystem Configuration ME VersionHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Bit ..\i386\Win7VistaIntel Bit ..\AMD64\Win7-64Vista64Intel Installing OS on a HDD Larger Than 2TB in RAID ModeWindows VistaTM 64-bit Page Windows 7 64-bit