ASRock Fatal1ty X79 Champion manual Hot Plug and Hot Swap for Sata / SATA2 HDDs, What is Hot Plug?

Page 64

2.19 Hot Plug and Hot Swap for SATA / SATA2 HDDs

This motherboard supports Hot Plug and Hot Swap for SATA / SATA2 in RAID / AHCI mode. Intel® X79 chipset provides hardware support for Advanced Host controller Interface (AHCI), a new programming interface for SATA host controllers developed through a joint industry effort.

NOTE

What is Hot Plug?

If the SATA / SATA2 HDDs are NOT set for RAID configuration, it is called “Hot Plug” for the action to insert and remove the SATA / SATA2 HDDs while the system is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has been installed into the SATA / SATA2 HDD.

What is Hot Swap?

If SATA / SATA2 HDDs are built as RAID 1 or RAID 5 then it is called “Hot Swap” for the action to insert and remove the SATA / SATA2 HDDs while the system is still power-on and in working condition.

2.20 Hot Plug and Hot Swap for SATA3 HDDs

This motherboard supports Hot Plug and Hot Swap for SATA3 in RAID / AHCI mode. Intel® X79 and Marvell SE9230 chipsets provide hardware support for Advanced Host controller Interface (AHCI), a new programming interface for SATA host controllers developed through a joint industry effort.

NOTE

What is Hot Plug?

If the SATA3 HDDs are NOT set for RAID configuration, it is called “Hot Plug” for the action to insert and remove the SATA3 HDDs while the system is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has been installed into the SATA3 HDD.

What is Hot Swap?

If SATA3 HDDs are built as RAID 1 or RAID 5 then it is called “Hot Swap” for the action to insert and remove the SATA3 HDDs while the system is still power-on and in working condition.

64

Image 64
Contents Fatal1ty X79 Champion Series Fatal1ty Story LIVIN’ Large Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Rear Panel I/O ConnectorUSB3.0 Bios Feature Unique FeatureSupport CD HardwareCertifications FCC, CE, WhqlPage Page Page Motherboard Layout LAN Port LED Indications I/O PanelTable for Audio Output Connection Pre-installation Precautions Screw HolesCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a Dimm Pcie Slot Configurations Expansion Slots PCI and PCI Express SlotsInstalling an expansion card ASRock Game Blaster Configuration Select a recording device Mic Volume Acoustic Echo CancellationMic Boost CrystalVoiceScout Mode Hot Key ConfigurationSpeakers / Headphones Configuration Optional Speakers CenterSubwoofer Rear pairMixer Equalizer Device Connected Play stereo mix to digital output Profile User ProfilesPage Requirements Installing Three SLITM-Ready Graphics Cards Two GoldfingersASRock 3-Way SLI Bridge Card Installing Four SLITM-Ready Graphics Cards Driver Installation and Setup Select Nvidia Control Panel tabFollow steps a to E on Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards Installing Four CrossFireXTM-Ready Graphics Cards For Windows 7 / VistaTM OS Surround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide Advanced Super IO Configuration CIR Controller EnabledCIR sensors in different angles Jumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsUSB 2.0 Headers Besides two default USB Consumer Infrared Module Header This header can be used to Chassis Speaker Header Please connect the chassis ATX Power Connector Ground pinPort on the I/O panel, there Hdmispdif Header Hdmispdif header, providing Installation Guide of Front USB 3.0 Panel Installation Guide of Rear USB 3.0 BracketSmart Switches 15 Dr. Debug Status Code DescriptionPage Page Post Status Checker PSC Serial ATA Sata / Serial ATA2 SATA2 Hard Disks Installation Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug? What is Hot Swap?Hot Plug and Hot Swap for Sata / SATA2 HDDs Hot Plug and Hot Swap for SATA3 HDDsSata power cable Sata / SATA2 / SATA3 HDD Hot Plug and Operation GuideHow to Hot Plug a Sata / SATA2 / SATA3 HDD Set up Uefi Driver Installation GuideUse RAID Installation Guide to set RAID configuration Page Untied Overclocking Technology Introduction Uefi Menu BarNavigation Keys Main ScreenOC Tweaker Screen Turbo Boost Power Limit Dram Timing Configuration Load XMP SettingDram Configuration Dram tCL Core Current LimitCommand Rate Dram Power Down ModeDram tRP Dram tRASMemory Power Savings Mode Memory ModeChannel Interleaving Rank InterleavingDram Fine Tuning SP Dram Fine Tuning SNVoltage Configuration CPU Core Voltage Dram tWWDDLoad Power Saving Mode User DefaultsDram Channel A/B CA Dram Channel A/B DQInstant Flash Advanced ScreenInternet Flash CPU Configuration CPU Thermal Throttling Enhance Halt State C1ECPU C3 State Support CPU C6 State SupportCore Current Limit North Bridge Configuration South Bridge Configuration Onboard Debug Port LED Storage Configuration Marvell 9230 SATA3M0M1M2M3 Operation Mode Marvell 9230 RAID ConfigurationSuper IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportIntel ME Subsystem Configuration ME Version ME SubsystemHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Bit ..\i386\Win7VistaIntel Bit ..\AMD64\Win7-64Vista64IntelWindows VistaTM 64-bit Page Windows 7 64-bit