ASRock Fatal1ty 990FX Professional Channel Interleaving, CAS# Latency tCL, Row Precharge Time tRP

Page 58

Channel Interleaving

It allows you to enable Channel Memory Interleaving. Configuration op- tions: [Disabled], [Auto]. The default value is [Auto].

CAS# Latency (tCL)

Use this item to change CAS# Latency (tCL) Auto/Manual setting. The default is [Auto].

RAS# to CAS# Delay (tRCD)

Use this item to change RAS# to CAS# Delay (tRCD) Auto/Manual setting. The default is [Auto].

Row Precharge Time (tRP)

Use this item to change Row Precharge Time (tRP) Auto/Manual setting. The default is [Auto].

RAS# Active Time (tRAS)

Use this item to change RAS# Active Time (tRAS) Auto/Manual setting. The default is [Auto].

Command Rate (CR)

Use this item to change Command Rate (CR) Auto/Manual setting. Min: 1T. Max: 2T. The default is [Auto].

RAS# Cycle Time (tRC)

Use this item to change RAS# Cycle Time (tRC) Auto/Manual setting. The default is [Auto].

Write Recovery Time (tWR)

Use this item to change Write Recovery Time (tWR) Auto/Manual setting. The default is [Auto].

Refresh Cycle Time (tRFC)

Use this item to change Refresh Cyle Time (tRFC) Auto/Manual setting. The default is [Auto].

RAS to RAS Delay (tRRD)

Use this item to change RAS to RAS Delay (tRRD) Auto/Manual setting. The default is [Auto].

Write to Read Delay (tWTR)

Use this item to change Write to Read Delay (tWTR) Auto/Manual setting. The default is [Auto].

Read to Precharge (tRTP)

Use this item to change Read to Precharge (tRTP) Auto/Manual setting. The default is [Auto].

Four Activate Window (tFAW)

Use this item to change Four Activate Window (tFAW) Auto/Manual setting. The default is [Auto].

58

Image 58
Contents Fatal1ty 990FX Professional Series Fatal1ty Story LIVIN’ Large Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Bios Feature ConnectorSmart Switch Rear Panel I/OHardware Unique FeatureSupport CD MonitorPage Page Page Motherboard Layout 24.4cm 9.6-inLAN Port LED Indications Table for Audio Output ConnectionPage Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Break NotchExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots Slitm and Quad Slitm Operation Guide RequirementsDriver Installation and Setup For Windows XP / XP 64-bit OS For Slitm mode onlySelect Nvidia Control Panel tab Select Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows XP OS For Windows 7 / VistaTM OSSurround Display Feature \ Surround Display InformationJumpers Setup Jumper SettingOnboard Headers and Connectors USB 3.0 Header Besides two default USB System Panel Header Chassis Speaker Header ATX Power Connector ATX 12V Power ConnectorFront USB 3.0 Panel Installation Guide Rear USB 3.0 Bracket Installation Guide Smart Switches11 Dr. Debug Status Code DescriptionPage Page Page What is Hot Swap Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Installing Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi Use RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Click Expert Mode Teaming Function Operation GuidePage Page From Control Panel, double-clickNetwork Connections Introduction Uefi Menu BarTo jump to the Exit Screen or exit the current screen Navigation KeysMain Screen System Time HourMinuteSecondOC Tweaker Screen North Bridge Maximum Frequency Dram Timing Control Power Down EnableProcessor Maximum Frequency Processor Maximum VoltageWrite Recovery Time tWR RAS# to CAS# Delay tRCDCommand Rate CR RAS to RAS Delay tRRDDram Voltage Would you like to save current setting user defaults?Voltage Control CPU Load-line calibration NB VoltageAdvanced Screen Instant FlashSecure Virtual Machine CPU ConfigurationCool ‘n’ Quiet Enhance Halt State C1ENorth Bridge Configuration Primary Graphics AdapterSouth Bridge Configuration Storage Configuration Hard Disk S.M.A.R.T Serial Port Address Super IO ConfigurationSerial Port Infrared PortAcpi Configuration USB Mouse Power On Acpi Hpet tableUSB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportChassis Fan 2 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 3 SettingBoot Screen Security Screen Exit Screen Running The Support CD Install Operating SystemSupport CD Information Drivers MenuInstalling OS on a HDD Larger Than 2TB