ASRock E35LM1 R2.0 manual Expansion Slot PCI Express Slot, Installing an expansion card, Pcie slot

Page 16

2.4 Expansion Slot (PCI Express Slot)

There is 1 PCI Express slot on this motherboard.

PCIE slot:

PCIE1 (PCIE x16 slot) is used for PCI Express x4 lane width graphics cards.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

16

Image 16

Contents E35LM1 R2.0 Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Support CD HardwareMonitor CertificationsPage Unique Features ASRock Instant BootASRock Instant Flash ASRock APP ChargerASRock Crashless Bios ASRock XFast USBASRock XFast LAN ASRock XFast RAMASRock Fast Boot ASRock Internet FlashASRock Uefi System Browser ASRock Dehumidifier FunctionMotherboard Layout SATA3 I/O Panel LAN Port LED IndicationsPre-installation Precautions Screw HolesInstallation of Memory Modules Dimm Installing a DimmExpansion Slot PCI Express Slot Installing an expansion cardPcie slot ASRock Smart Remote Installation Guide Advanced Super IO Configuration CIR Controller EnabledCIR sensors in different angles Jumpers Setup DescriptionOnboard Headers and Connectors Front Panel Audio Header Chassis Speaker Header Please connect the chassis Serial port Header What is Hot Plug Function? Serial ATA3 SATA3 Hard Disks InstallationHot Plug Function for SATA3 HDDs SATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD How to Hot Unplug a SATA3 HDDDriver Installation Guide Installing Windows XP / XP 64-bit Without RAID FunctionsUsing SATA3 HDDs without NCQ function Set up Uefi Install Windows XP / XP 64-bit OS on your systemUsing SATA3 HDDs with NCQ function Set up Uefi Introduction Uefi Menu BarNavigation Keys Main ScreenNavigation Keys + / Tab Enter Pgup Pgdn Home F10 F12Dram Timing Configuration Dram Frequency Dram Timing Control Power Saving ModeOC Tweaker Screen Bank InterleavingRAS# to CAS# Delay tRCD Command Rate CRWrite Recovery Time tWR RAS to RAS Delay tRRDVoltage Configuration Dram Voltage FCH Voltage+1.8V Voltage +1V VoltageAdvanced Screen CPU Configuration SVM ModeC6 Mode Cool ‘n’ QuietPrimary Graphics Adapter North Bridge ConfigurationShare Memory South Bridge Configuration Storage Configuration Sata ModeSata Aggressive Link Power Management Sata ControllerSuper IO Configuration Serial PortSerial Port Address CIR ControllerAcpi Configuration CSM USB 2.0 Controller USB ConfigurationLegacy USB Support Uefi Update Utility Instant Flash ToolSystem Browser OMGOnline Management GuardNetwork Configuration Internet Setting Dehumidifier CPU Fan SettingWould you like to save current setting user defaults? Uefi Download ServerHardware Health Event Monitoring Screen Boot Screen Fast BootBoot From Onboard LAN Setup Prompt TimeoutBoot Failure Guard Boot Failure Guard CountFull Screen Logo AddOn ROM DisplaySecure Boot Security ScreenLoad Uefi Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB