ASRock E35LM1 R2.0 Driver Installation Guide, Using SATA3 HDDs without NCQ function Set up Uefi

Page 27

2.11 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.12 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit Without RAID Functions

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP

/XP 64-bit OS on your SATA3 HDDs without RAID functions, please follow below procedures according to the OS you install.

2.12.1 Installing Windows® XP / XP 64-bit Without RAID Functions

If you want to install Windows® XP / XP 64-bit OS on your SATA3 HDDs without RAID functions, please follow below steps.

AHCI mode is not supported under Windows® XP / XP 64-bit OS.

Using SATA3 HDDs without NCQ function

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Configuration. B. Set the option “SATA Mode” to [IDE].

STEP 2: Install Windows® XP / XP 64-bit OS on your system.

27

Image 27

Contents E35LM1 R2.0 Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Certifications Support CDHardware MonitorPage ASRock APP Charger Unique FeaturesASRock Instant Boot ASRock Instant FlashASRock XFast RAM ASRock Crashless BiosASRock XFast USB ASRock XFast LANASRock Dehumidifier Function ASRock Fast BootASRock Internet Flash ASRock Uefi System BrowserSATA3 Motherboard LayoutLAN Port LED Indications I/O PanelScrew Holes Pre-installation PrecautionsInstalling a Dimm Installation of Memory Modules DimmInstalling an expansion card Expansion Slot PCI Express SlotPcie slot Advanced Super IO Configuration CIR Controller Enabled ASRock Smart Remote Installation GuideCIR sensors in different angles Description Jumpers SetupOnboard Headers and Connectors Front Panel Audio Header Chassis Speaker Header Please connect the chassis Serial port Header Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?Hot Plug Function for SATA3 HDDs Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Unplug a SATA3 HDD How to Hot Plug a SATA3 HDDInstall Windows XP / XP 64-bit OS on your system Driver Installation GuideInstalling Windows XP / XP 64-bit Without RAID Functions Using SATA3 HDDs without NCQ function Set up UefiUsing SATA3 HDDs with NCQ function Set up Uefi Uefi Menu Bar IntroductionF10 F12 Navigation KeysMain Screen Navigation Keys + / Tab Enter Pgup Pgdn HomeBank Interleaving Dram Timing Configuration Dram FrequencyDram Timing Control Power Saving Mode OC Tweaker ScreenRAS to RAS Delay tRRD RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWR+1V Voltage Voltage Configuration Dram VoltageFCH Voltage +1.8V VoltageAdvanced Screen Cool ‘n’ Quiet CPU ConfigurationSVM Mode C6 ModeNorth Bridge Configuration Primary Graphics AdapterShare Memory South Bridge Configuration Sata Controller Storage ConfigurationSata Mode Sata Aggressive Link Power ManagementCIR Controller Super IO ConfigurationSerial Port Serial Port AddressAcpi Configuration CSM USB Configuration USB 2.0 ControllerLegacy USB Support OMGOnline Management Guard Uefi Update Utility Instant FlashTool System BrowserUefi Download Server Network Configuration Internet SettingDehumidifier CPU Fan Setting Would you like to save current setting user defaults?Hardware Health Event Monitoring Screen Setup Prompt Timeout Boot ScreenFast Boot Boot From Onboard LANAddOn ROM Display Boot Failure GuardBoot Failure Guard Count Full Screen LogoSecurity Screen Secure BootDiscard Changes and Exit Load Uefi DefaultsExit Screen Save Changes and ExitDrivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB