ASRock FM2A55M-VG3 manual Front Panel Audio Header

Page 25

Front Panel Audio Header

 

 

GND

(9-pin HD_AUDIO1)

 

 

 

 

PRESENCE#

 

 

 

 

 

 

MIC_RET

 

 

 

 

 

 

 

 

 

 

 

OUT_RET

(see p.13 No. 20)

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT2_L

 

 

 

 

 

 

 

 

J_SENSE

 

 

 

 

 

 

 

OUT2_R

 

 

 

 

 

MIC2_R

 

 

 

MIC2_L

This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the “FrontMic” Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.13 No. 14)

functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con- figure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to per- form a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

25

Image 25
Contents FM2A55M-VG3 Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Bios Feature ConnectorSupport CD HardwarePage ASRock Extreme Tuning Utility Axtu Unique FeaturesASRock Instant Boot ASRock Instant FlashASRock XFast USB ASRock APP ChargerASRock XFast LAN ASRock XFast RAMASRock Easy RAID Installer ASRock Crashless BiosASRock OMG Online Management Guard ASRock Internet FlashASRock Interactive Uefi ASRock Fast BootASRock X-Boost ASRock Restart to UefiFM2 Motherboard LayoutLAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots Enjoy the benefit of AMD Dual Graphics AMD Dual Graphics Operation GuideWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Multi Monitor Feature Page Description Jumpers SetupSerial ATA2 Connectors Onboard Headers and ConnectorsFront Panel Audio Header Chassis Speaker Header Please connect an ATX power supply to this connector ATX Power ConnectorWhat is Hot Plug Function? Serial ATA2 SATA2 Hard Disks InstallationWhat is Hot Swap Function? Hot Plug and Hot Swap Functions for Serial ATA2 SATA2 HDDsPoints of attention, before you process the Hot Plug SATA2 HDD Hot Plug Feature and Operation GuideHow to Hot Unplug a SATA2 HDD How to Hot Plug a SATA2 HDDSet up Uefi Driver Installation GuideUse RAID Installation Guide to set RAID configuration Page Uefi Menu Bar IntroductionMain Screen Navigation KeysNavigation Keys + / Tab Enter Pgup Pgdn Home F10 F12OC Tweaker Screen Multiplier/Voltage Change Dram Timing Configuration Dram FrequencyBoost Frequency Multiplier CPU Frequency MultiplierVoltage Configuration Dram Voltage Power Down EnableDram Timing Control Dram Slot Dram Timing ControlAdvanced Screen Core C6 Mode CPU ConfigurationPackage C6 Mode Cool ‘n’ QuietPrimary Graphics Adapter North Bridge ConfigurationShare Memory Dual GraphicsOnboard HD Audio South Bridge ConfigurationFront Panel Onboard LANSata Mode Storage ConfigurationEasy RAID Installer Sata ControllerAcpi Configuration Acpi Hpet table USB 2.0 Controller USB ConfigurationLegacy USB Support Tool Uefi Update Utility Instant FlashSound Effect System BrowserDehumidifier CPU Fan Setting Network Configuration Internet SettingInternet Flash Uefi Download ServerWould you like to save current setting user defaults? Hardware Health Event Monitoring Screen Fast Boot Boot ScreenBoot From Onboard LAN Setup Prompt TimeoutBoot Failure Guard Count Boot Failure GuardFull Screen Logo AddOn ROM DisplaySecurity Screen Secure BootExit Screen Load Uefi DefaultsSave Changes and Exit Discard Changes and ExitSupport CD Information Install Operating SystemRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB Drv4E CtrlB5 Langeng Installing OS on a HDD Larger Than 2TB in RAID ModeChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 8 64-bit / 7 64-bit