ASRock X79 Extreme4-M manual Select Nvidia Control Panel tab, Select Control Panel tab

Page 24

For Windows® VistaTM / VistaTM 64-bit / 7 / 7 64-bit OS: (For SLITM and Quad SLITM mode)

A. Click the Start icon on your Windows taskbar.

B. From the pop-up menu, select All Programs, and then click NVIDIA Corporation.

C. Select NVIDIA Control Panel tab.

D. Select Control Panel tab.

E. From the pop-up menu, select Set SLI and PhysX configuration. In Set PhysX GPU acceleration item, please select Enabled. In Select an SLI configuration item, please select Enable SLI. And click Apply.

F. Reboot your system.

G. You can freely enjoy the benefit of SLITM or Quad SLITM feature.

*SLITM appearing here is a registered trademark of NVIDIA® Technologies Inc., and is used only for identification or explanation and to the owners’ benefit, without intent to infringe.

24

Image 24

Contents X79 Extreme4-M Copyright Notice DisclaimerContents Uefi Setup Utility Introduction Uefi Menu BarPackage Contents IntroductionSpecifications Connector Smart SwitchBios Feature USB3.0Unique Feature Support CDHardware MonitorPage Page Page Motherboard Layout I/O Panel LAN Port LED IndicationsOff No Link Blinking LinkPage Pre-installation Precautions Screw HolesCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink With fan operation or contact other componentsInstallation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI and PCI Express SlotsSlitm and Quad Slitm Operation Guide RequirementsASRock SLIBridge Card Driver Installation and Setup For Windows XP / XP 64-bit OS For Slitm mode onlyDouble-click Nvidia Settings icon on your Windows taskbar Select Nvidia Control Panel tab Select Control Panel tabInstalling Two CrossFireXTM-Ready Graphics Cards CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge Install the required drivers to your system For Windows XP OSFor Windows 7 / VistaTM OS Surround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide CIR sensors in different anglesASRock XFast Charger Operation Guide Jumpers Setup DescriptionClear Cmos Jumper Onboard Headers and Connectors Serial Ataii ConnectorsSerial ATA3 Connectors Serial ATA Sata Data CableUSB 3.0 Header Besides two default USB Optional wireless transmittingPorts on the I/O panel, there is One USB 3.0 header on thisPower LED Header Please connect the chassis Power LED to this header toIndicate system power status Power offATX Power Connector Supply to this connectorATX 12V Power Connector Smart Switches 15 Dr. Debug Status Code DescriptionPage Page Page Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function? What is Hot Swap Function?Hot Plug and Hot Swap Functions for Sata / Sataii HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Plug Points of attention, before you process the Hot UnplugDriver Installation Guide Set up UefiUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Install Windows XP / XP 64-bit OS on your systemUntied Overclocking Technology Introduction Uefi Menu BarNavigation Keys Main ScreenNavigation Keys F10OC Tweaker Screen Turbo Boost Power Limit Dram Timing Control Load XMP SettingCore Current Limit Additional Turbo VoltageCommand Rate CR Dram Power Down ModeDram tRP Dram tRASPhase Shedding Memory Power Savings ModeMemory Test When Fast Boot Memory Fast BootLoad Power Saving Mode User DefaultVoltage Control CPU Core Voltage CPU Load-Line CalibrationAdvanced Screen System BrowserInstant Flash CPU Configuration CPU Thermal Throttling Enhance Halt State C1ECPU C3 State Support CPU C6 State SupportNorth Bridge Configuration South Bridge Configuration Storage Configuration Super IO Configuration Use this item to enable or disable the onboard serial portSerial Port Serial Port AddressAcpi Configuration USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportIntel ME Subsystem Configuration ME Version ME SubsystemHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Copy Intel RAID drivers into a USB flash diskWindows VistaTM 64-bit Page Windows 7 64-bit