ASRock Z77 OC Formula manual Installation Guide of Front USB 3.0 Panel

Page 46

The Installation Guide of Front USB 3.0 Panel

Step 1 Prepare the bundled Front USB 3.0 Panel, four Step 2 HDD screws, and six chassis screws.

Screw the 2.5” HDD/SSD to the Front USB 3.0 Panel with four HDD screws.

Step 3

Step 5

Intall the Front USB 3.0 Panel into the 2.5” drive bay of the chassis.

Plug the Front USB 3.0 cable into the USB 3.0 header (USB3_6_7) on the motherboard.

Step 4

Step 6

Screw the Front USB 3.0 Panel to the drive bay with six chassis screws.

The Front USB 3.0 Panel is ready to use.

The Installation Guide of Rear USB 3.0 Bracket

Step 1

Unscrew the two screws from the Front USB 3.0 Step 2 Panel.

Put the USB 3.0 cable and the rear USB 3.0 bracket together.

Step 3

Screw the two screws into the rear USB 3.0 bracket.

Step 4

Put the rear USB 3.0 bracket into the chassis.

46

Image 46
Contents Z77 OC Formula Copyright Notice DisclaimerContents Main Screen OC Tweaker Screen Advanced Screen Acpi ConfigurationIntroduction Uefi Menu Bar Utilities MenuPackage Contents IntroductionSpecifications Graphics Clear Cmos Switch with LEDCrossFireXTM Supports Nvidia Quad Slitm and Slitm AudioUSB3.0 ConnectorRAID RAID 0 and RAID 1, NCQ, Ahci and Hot Plug Functions Ports, supports USB 1.0/2.0/3.0 up to 5Gb/sUnique Feature Support CDMonitor HardwareCertifications Page Page Page Motherboard Layout Off No Link Blinking I/O PanelLAN Port LED Indications LinkPage Pre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationInstalling a Dimm Notch break BreakThere are 5 PCI Express slots on this motherboard Pcie Slot ConfigurationsExpansion Slots PCI Express Slots Pcie slotsInstalling an expansion card Slitm and Quad Slitm Operation Guide RequirementsASRock SLIBridge2S Card For Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and SetupDouble-click Nvidia Settings icon on your Windows taskbar Select Nvidia Control Panel tab Select Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards For Windows XP OS Install the required drivers to your systemFor Windows 7 / VistaTM OS Page For Windows XP / XP 64-bit OS Surround Display FeatureSelect the display icon identified by the number For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS What is HDCP? Hdcp FunctionMake sure the option CIR Controller is setting at Enabled ASRock Smart Remote Installation GuideInstall Multi-Angle CIR Receiver to the front USB port Advanced Super IO Configuration CIR Controller EnabledCIR sensors in different angles Description Jumpers SetupBios Selection Jumper Clear Cmos JumperSerial ATA3 Connectors Onboard Headers and ConnectorsSerial ATA2 Connectors Serial ATA Sata Data CableOptional wireless transmitting USB 2.0 Headers Besides four default USBUSB 3.0 Header Besides six default USB Three USB 2.0 headers on thisSystem Panel Header Front Panel Audio HeaderSeveral system front panel Indicate system power status Power LED Header Please connect the chassisPower LED to this header to State power offSupply to this connector CPU Fan ConnectorsATX Power Connector ATX 12V Power ConnectorsDMI, PCH2, PCH Serial port moduleIncluding VCCM, Vccsa 8VPLLInstallation Guide of Front USB 3.0 Panel Installation Guide of Rear USB 3.0 BracketClear the Cmos values Smart SwitchesAdjust OC frequency in Rapid + / Rapid OC Buttons + / Rapid OC Buttons allowPCIE4 PCIE2PCIE5 14 Dr. Debug Status Code DescriptionPage Page Page Serial ATA3 SATA3 Hard Disks Installation Serial ATA Sata / Serial ATA2 SATA2 Hard Disks InstallationPost Status Checker PSC Hot Plug and Hot Swap Functions for Sata / SATA2 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug Points of attention, before you process the Hot Plug Points of attention, before you process the Hot UnplugSet up Uefi Driver Installation GuideUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Install Windows XP / XP 64-bit OS on your systemPage Introduction Uefi Menu BarNavigation Keys + / Tab Enter Pgup Pgdn Home Navigation KeysMain Screen F10 F12OC Tweaker Screen Spread Spectrum Long Duration Power LimitShort Duration Power Limit Intel SpeedStep TechnologyDram Configuration Dram tCL Dram Timing Configuration Load XMP SettingDram Timing Mode Dram FrequencyDram tWR Command Rate CRMemory Performance Level Dram tRFCCommand 3-state MRC Fast BootForce Cold Reset TRRDRVoltage Configuration Dimm Exit ModePower Down Mode PWM Switching FrequencyAdvanced Screen CPU Configuration Hardware Prefetcher No-Execute Memory ProtectionIntel Virtualization Technology Use this item to turn on/off the MLC streamer prefetcherNorth Bridge Configuration South Bridge Configuration Storage Configuration Bootable Marvell SATA3 Controller Entry After IntelR Rapid Start TechnologyIntelR Rapid Start Technology Active Page Threshold SupportIntelR Smart Connect Technology IntelR Smart Connect TechnologySerial Port Super IO ConfigurationUse this item to enable or disable the onboard serial port Serial Port AddressAcpi Configuration USB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportSound Effect Uefi Update Utility Instant FlashTool System BrowserInternet Flash Network Configuration Internet SettingDehumidifier CPU Fan Setting Uefi Download ServerHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Contact InformationInstalling OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Bit ..\i386\Win7VistaIntel Bit ..\AMD64\Win7-64Vista64IntelWindows VistaTM 64-bit Page Windows 7 64-bit
Related manuals
Manual 270 pages 58.16 Kb