MSI Keeper 945GME IDE Primary/Secondary Master/Slave PIO, IDE Primary/Secondary Master/Slave Udma

Page 50

MS-9641 Mainboard

[Disabled] to deactivate an interface, if you install a primary and/or second- ary add-in IDE interface.

IDE Primary/Secondary Master/Slave PIO

The IDE PIO (Programmed Input/Output) fields let you set a PIO mode for the IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In [Auto] mode, the system automatically determines the best mode for each device.

IDE Primary/Secondary Master/Slave UDMA

Ultra DMA 33/66/100/133 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows ME, XP or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/33, Ultra DMA/66, Ultra DMA/100 and Ultra DMA/133, select [Auto] to enable BIOS support.

* On-Chip Serial ATA Setting *

SATA Mode

This setting specifies the SATA controller operation mode.

On-Chip Serial ATA

This setting specifies the function of the on-chip SATA controller.

[Disabled]	Disable SATA controller
[Auto]	Automatically determined by BIOS
[Enhanced Mode]	Enable both SATA and PATA, max. 6 IDE
	drives supported
[SATA Only]	SATA operates in legacy mode

SATA Port Speed Settings

This setting controls the speed of the SATA port.

PATA IDE Mode / SATA Port

These settings specify the modes of the PATA & SATA ports.

3-12

Image 50

Contents MS-9641 V2.X Mainboard G52-96411x1Revision History Copyright NoticeTrademarks Technical SupportSafety Instructions Micro-Star International MS-9641 FCC-B Radio Frequency Interference StatementWeee Waste Electrical and Electronic Equipment Statement Page Vii Contents Getting Started Getting StartedLAN Mainboard SpecificationsFSB IDEForm Factor Getting Started Watch Dog TimerAccessory MountingMainboard Layout MS-9641 v2.X Micro-ATX MainboardHardware Setup Hardware SetupQuick Components Guide CPU Central Processing Unit CPU & Cooler Set Installation Hardware Setup DDR2 MemoryMemory Population Rules Installing Memory Modules ATX 12V Power Connector JPW0 Power SupplyATX 24-Pin Power Connector ATX1 ATX1Front Panel Serial Port ConnectorUSB Connectors MS-9641 Mainboard LAN RJ-45 Jack LEDCompact Flash Card Slot CF0 ConnectorsHard Disk Connector IDEB0 IDEB0Serial Ataii Connectors SATA1~SATA4 SATA4 SATA3 SATA2 SATA1Fan Power Connectors CPUFAN0, SYSFAN1, AUXFAN0 Front Panel Connectors JFP1USB 2.0 Bracket Front USB Connector FUSB2FUSB2 Serial Port Connector COM SMBus Connector SmbusTV-Out Connector JTV0 FWH/LPC Debugging connector JLPC1 LCD Module Connector JLCD1Keyboard/Mouse Connector J0 JLCD1Lanled LAN ByPass LED Pinheader J3Cpld Data Reflash PinheaderJP1 JP1Bypass setting in Bios MS-9641 Mainboard LAN Bypass DefinitionProgramming Guide Bit DefinitionMS-9641 Mainboard Signal Action Segment Signal Name Description Type BypassHardware Setup Sample code Method 1 Gpio Mode MS-9641 Mainboard Method 1 Gpio control Bypass Gpio ModeMethod 2 LPC Control Bypass LPC Mode Sample Code Method 2 LPC Mode Hardware Setup Watch Dog function setup sample codeJumpers Clear Cmos Jumper CLRCMOS0Jcfvsel AT/ATX Power Select Jumper J5Gmch Voltage Jumper J2 PCI Peripheral Component Interconnect Slot SlotGolden Finger TOP View B94 Bottom View A94Bios Setup Bios SetupEntering Setup Press F1 to enter SetupGeneral Help F1 Control KeysGetting Help Main MenuMenu Bar Time hhmmss MainDate mmddyy IDE Channel 0 Master/Slave, IDE Channel 1 Master/SlaveCylinder Access M odeCapacity HeadCPU L3 Cache Advanced Bios Features Virus WarningAdvanced Agent after boot Quick Power On Self TestApic Mode MPS Version Control For OSPrecharge Delay tRAS Bios Setup Advanced Chipset Features Dram Timing SelectableDram RAS# to CAS# Delay CAS Latency TimePEG/Onchip VGA Control MS-9641 Mainboard VGA SettingBoot Display On-Chip Frame Buffer SizeIDE DMA Transfer Access On-Chip Primary/Secondary PCI IDEPata IDE Mode / Sata Port On-Chip Serial ATA Setting Sata ModeSata Port Speed Settings IDE Primary/Secondary Master/Slave PIOUSB Controller, USB 2.0 Controller PXE BootPlanar Ethernet #01/ #02/ #03/ #04/ #05/ #06 USB Keyboard/Mouse SupportUR2 Duplex Mode Uart Mode SelectIR Transmission Delay Use IR PinsPower Management Setup Power Type Bios Setup Watch Dog ActionWatch Dog Timer Minutes COM Port SelectTime hhmmss Alarm Resume by AlarmDate of Month Alarm Boot Up NumLock StatusSpread Spectrum Boot First / Second / Third Boot Device Bios Setup Hard Disk Boot PriorityCD-ROM This setting Refer to Boot Priority Boot Other DeviceSecurity Set Supervisor PasswordSet User Password Security OptionHalt On SystemSystem Summary PC Health Smart Fan SettingSmart SYSFan1 / CPUFan1 / SYSFan2 Temperature Bios Setup SYSFan1 / CPUFan1 / SYSFan2 Tolerance Value Save & Exit Setup Load Fail-Safe DefaultsLoad Optimized Defaults Exit