Teka TSE 342A Transport instructions, Disposal, Appliance setup, Electrical connections, Location

Page 6

en

en

Transport instructions

The appliance should be transported only in upright position.

The packing as supplied must be intact during transportation.

If the appliance is transported in the horizontal position, it must be placed vertically and left in this position for 4 hours before taking into operation.

The appliance must be protected against rain, moisture and other atmospheric influences. The manufacturer assumes no liability if safety instructions are disregarded.

Disposal

Make the appliance unusable immediately. Pull out the mains plug and cut the power cable. Remove or destroy snap or latch locks before disposing of the appliance. In this manner you prevent children from locking themselves in and endangering their lives.

Appliance setup

Do not operate your appliance in a room where the temperature is likely to fall below 10 °C at night and/or especially in winter. At lower temperatures the appliance may not operate, resulting in a reduction in the storage life of the food.

The climate class rate of your appliance is given on the rating label located inside the appliance. It specifies the appropriate operating ambient temperatures as explained below.

Climatic class

Ambient temperatures

SN

+10 °C to 32 °C

N

+16 °C to 32 °C

ST

+18 °C to 38 °C

T

+18 °C to 43 °C

SN-ST

+10 °C to 38 °C

SN-T

+10 °C to 43 °C

Location

Only place the appliance, as shown in the illustration in dry rooms which can be aired.

Avoid direct sunlight or direct heat sources such as a stove or a heater.

If this cannot be avoided, the following minimum distances should be maintained: Electric stoves: 3,00 cm

Heater: 3,00 cm

Cooling devices: 2,50 cm

Ensure sufficient air circulation for your device.

Make sure that sufficient room is provided around the appliance to ensure free air circulation.

Fit the two plastic wall spacers supplied with the appliance rotating 1/4 turn to the condenser at the back of the appliance (Fig. 5).

The appliance should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that your appliance is standing upright adjust the two front feet by turning clockwise or counter-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise.

Electrical connections

Warning

This appliance must be grounded.

Check whether the power type and voltage in your region corresponds to the one stated on the rating label inside the appliance.

The electrical safety of the appliance is only assured when the grounding system in the house is installed in accordance with regulations.

When placing the appliance, do not let the power cable get stuck under it; otherwise the cable will be damaged.

Ensure that the plug remains readily accessible. Do not use a multiple adapter bar or an extension cable.

The electrical specifications of your appliance is given on the rating label located inside the appliance.

Route power cable to allow easy connection and disconnection after installation.

A contact separator should be used if the power cable is not accessible. (for built-in models)

2

Image 6
Contents TSE TSE 342 a En-Index De-InhaltFr-Index Pt-ÍndiceTSE Page Safety comes first Disposal Appliance setupTransport instructions Electrical connectionsGet to know your appliance Prior to startupControl Panel Control Functions Freezer Set Quick FridgeQuick Freeze Alarm Icon Actual Fridge TemperatureActual Freezer Temperature Fridge Bar Graphs /gCooling Defrosting of the applianceFood storage Freezing Freezing foodDoor shelves Cleaning and careSwitch off at the socket outlet and pull out the mains plug Collecting container PanPractical tips and notes CoolingFreezing Examples of Use Normal operating noisesWhat, if Reversing the doors Door Open AlarmThere is actual freezer temperature failure Other possible malfunctionsNoise Meaning of energy fiche Only for information purposePage Teka Group Teka Industrial S.A Teka Küchentechnik GmbH