Lennox International Inc MPB35ST-NM manual Vent Operation Test, Spill Switch Operation

Page 5

Millivolt appliances are fitted with an OFF/ON Rocker Switch located behind the control compartment access panel, below the appli- ance front glass enclosure panel (see Figure 1 for location). Once the pilot is lit, the OFF/ON rocker switch will control the appliance OFF/ON burner operation. To operate: Toggle the switch between its ON and OFF positions.

If your millivolt appliance is equipped with an optional remote switch kit (wall switch or remote control) and the pilot is lit, the appliance main burner may be turned on and off using the optional switch. When using an optional remote switch, turn off the standard OFF/ON switch.

Note: To prevent excessive resistance in burner circuit (which can cause burner operation prob- lems), only one burner control switch should be wired to valve. Therefore, if an optional control switch is installed, the standard Off/On switch and wires should be removed.

Electronic Appliances -

To light electronic appliances refer to the detailed lighting instructions found on Pagex

19.Electronic appliance lighting instructions mayalsobefoundonthepulloutlightinginstruc- tion labels attached to the gas control valve.

Once the pilot is lit, if your electronic appliance is equipped with an optional burner control switch kit the appliance main burner may be turned on and off using the optional switch (See Optional Accessories on Pagex 15 - wall switch, or remote control Receiver).

Honeywell Electronic Gas Valve

Manifold

Pressure ON / OFF Switch

Port

 

 

 

Inlet

C

 

 

Pressure

ONTROL

OFF ON

N

Port

 

 

I

 

IGNITER

 

 

 

 

 

IPS

 

Figure 3

Electronic Gas

Control Valve

 

Variable Flame Height Adjustment ( Millivolt Appliances only)

1. All Millivolt appliances are equipped with a variable gas control valve. Flame height for these models may be adjusted through a range between fixed low and high settings while the appliance is in operation. Adjust the flame height as desired after lighting the appliance by rotating the variable adjustment control knob (HI/LO) located on the front of the valve (refer to Figure 2 ).

2.During the first initial burns of these appli- ances, there will be some odor emitted (see Burn-In Period on Page 3 ).

3.Keep the lower control compartment clean by vacuuming or brushing at least twice a year. More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, pet hair, etc. It is very important that the control compartments, burners and circulating air passageways of the appliance are kept clean.

4.Always turn off gas to the pilot (millivolt appliances) and let the appliance cool down before cleaning. Before re-lighting, refer to the lighting instructions in this manual. Lighting instructions may also be found on the pull out lighting instruction labels attached to the gas control valve.

5.Always keep the appliance area clear and free from combustible materials, gasoline and other flammable liquids.

6.Remember, Millivolt appliances have a con- tinuous burning pilot flame. Exercise cau- tion when using products with combustible vapors.

VENT OPERATION TEST

A vent operation test is required as part of the installation to verify that proper venting condi- tions exist and should be done periodically to ensure nothing has changed that would affect proper venting of the appliance.

Procedure:

1.ENSURE APPLIANCE IS OFF (PILOT ONLY) AND COOL.

2.Open both latches on one of the glass enclosure doors and slightly prop it open at the bottom (approx. 1/4” gap). See Figure 6 on Page 9.

3.Turn on all the exhaust fans in the dwelling (and any other appliances which remove air from the dwelling, such as a furnace or clothes dryer, etc.).

4.Ensure that all the doors and windows in the room where the fireplace is located are closed.

5.Light the appliance (see Lighting Instruc- tions, Pages 18 & 19 ). Adjust flame height to highest setting and operate for approximately 5-10 minutes. Do not leave appliance unattended.

6.Take a smoke producing device and move it alongthebottomedgeoftheglassdoor(where it is cracked open). If smoke is drawn into the firebox, the vent operation is adequate.

IF THE SMOKE IS NOT DRAWN INTO THE FIREBOX, TURN THE APPLIANCE OFF AND CALL A QUALIFIED SERVICE TECHNICIAN.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

SPILL SWITCH OPERATION

Manual-Reset (safety limit) Spill Switch This appliance is equipped with a (safety limit) spill switch that is designed to "trip" and discon- nect the burner circuit if flue spillage occurs (because of improper venting of combustion products or vent blockage). If, during appliance operation, the burner flame goes out (indepen- dently of the burner OFF/ON wall switch), it may be due to the operation of this (safety limit) spill switch. If this switch "trips" it will need to be manually reset by pressing the reset button on switch (see Figure 4 ).

Procedure to Reset (safety limit) Spill Switch

ALLOW APPLIANCE TO COOL COMPLETELY BEFORE ACCESSING AND RESETTING

To access the spill switch:

1.Pull off the top louvered panel.

2.Locate and press the red reset button on the switch (it will click & lock in).

The appliance should then relight and remain lit. If this does not occur, turn off the appliance and call a qualified service technician.

 

 

Press Reset Button on

 

 

Spill Switch

 

 

Remove Top

 

 

Louvered

 

 

Panel (or

 

 

optional

 

 

radiant panel,

 

 

if applicable)

Figure 4

-

Spill Switch

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Listing Agency OTL Report No -F-27-5 875,024M REV. NC 04/2005MPB35ST-NMMPB35ST-NE MPB35ST-PM Congratulations Burn-in Period Safety & Warniing InformationOrifice Sizes Sea Level to High Altitude All Models Burner Orifice Sizes all models Elevation Natural PropaneMillivolt Appliances Operation and Care of Your ApplianceSIT Millivolt Valve see FigureEnsure Appliance is OFF Pilot only and Cool Spill Switch OperationVent Operation Test Glass Front MaintenanceOutside Combustion Air Controls See Figure CA B Top View of Logs Top View of Logs InstalledLOG SET ReferenceRead LOG Warnings on page 9 Before Proceeding Placement of Glowing EmbersRemove front glass enclosure panel from appliance Position The Groove in The Back of Log CAir Shutter Adjustment Guidelines Burner Adjustments Qualified Technicians onlyThis appliance is not designed to burn wood. Any attempt to Flame Appearance & SootingWhile HOT Maintenance Task Accomplishing Person ProcedureSymptom Possible Causes Corrective Action TroubleshootingSwitch or remote control Operation, the standard burnerTroubleshooting Procedure Electronic Ignition System Replacement Parts WarrantyWiring Diagrams Lennox Hearth ProductsAccessory Components Brickaded Panel Liner Kit Clean Face Panel KitsScreen Heat Guard Kit Door Frame KitsPolished Brass and Brushed Stainless Hood Kits Arch Door KitsPiece Polished Brass and Brushed Stainless Louvers Kits Outside Air Kits Models FOAK-4 and FOAK-4LDLighting Instructions Normal service To OFF. Do not forceTo Turn OFF GAS to Appliance What to do if YOU Smell GASWhat to do if YOU Smell GAS SwitchClose lower control compartment door To Shut OFFWest Taft Avenue Orange, CA Replacement Parts MPB35ST20 P/N 875,024M REV. NC 04/2005

MPB35ST-NM specifications

Lennox International Inc., a leader in the heating, ventilation, and air conditioning (HVAC) industry, offers the MPB35ST-NM model as part of its comprehensive range of integrated solutions. This finely engineered unit is designed to provide exceptional performance and energy efficiency while ensuring optimum home comfort.

One of the standout features of the Lennox MPB35ST-NM is its modular design, which allows for flexible installation and easy integration with existing systems. This unit is particularly beneficial for residential settings where space may be at a premium. It also supports efficient zoning, enabling tailored climate control for different areas of the home.

The MPB35ST-NM utilizes advanced multi-stage heating technology, which means it can adjust its output to match the specific demands of the environment. This significantly enhances energy efficiency and reduces operational costs. The unit operates with a high Seasonal Energy Efficiency Ratio (SEER) rating, ensuring optimal performance without excessive energy consumption.

Additionally, the MPB35ST-NM is equipped with smart technology features that allow homeowners to monitor and manage their heating system remotely. Through a user-friendly app, users can adjust settings, schedule maintenance reminders, and receive performance alerts, all of which contribute to an improved user experience.

Another key characteristic of the MPB35ST-NM is its quiet operation. The unit is designed with sound-dampening components that minimize noise during operation, ensuring that homeowners can enjoy a peaceful living environment.

Durability is another hallmark of Lennox products, and the MPB35ST-NM is no exception. Constructed with high-quality materials, this unit is built to withstand the rigors of daily use while offering long-lasting reliability. Additionally, Lennox provides robust customer support and warranty options, giving customers peace of mind in their investment.

In summary, the Lennox International Inc. MPB35ST-NM model stands out as a leader in home heating solutions. With its adaptable design, energy-efficient technology, smart features, quiet operation, and dependable durability, it meets the evolving needs of modern households, making it an excellent choice for those seeking comfort and efficiency in their heating systems.
Top Page Image Contents