NuTone LA500K warranty Recommended NEW Construction Wiring, Replacing Existing 2-NOTE Chime

FOUR NOTE DOOR CHIME
	RECOMMENDED NEW CONSTRUCTION WIRING
To register this product, visit: www.nutone.com	Ground
		OPTIONAL: 2 or 3 chimes can be connected to a single transformer. 2 chimes
		require transformer Model C909 or C907. 3 chimes require transformer Model C907.
READ AND SAVE THESE INSTRUCTIONS	120 VAC

PLAN THE INSTALLATION										Lighted or
This chime will accomodate up to three (3) entrances. Pushbuttons connected to the “FRONT” terminal play a 4 or
										Unlighted Buttons
8 note melody. Pushbuttons connected to the “SIDE” and “REAR” terminals play separate single notes. In order to			16 VAC				Front	Side	Rear
cycle through the 4 or 8-note melody, the chime must have a constant source of power.			Transformer
NEW CONSTRUCTION INSTALLATIONS (Figure 1)				1	2	3	F	S	R	NOT USED
The transformer provides constant power to terminals 2 and 3 and also provides power to light the pushbutton(s).		9-volt
REPLACING AN EXISTING 2-NOTE CHIME (Figure 2)		batteries		Volume Control						(Figure 1)
		not used
Two 9-volt batteries provide constant power to the chime, while the transformer provides power to light the
pushbutton(s).
INSTALLATION		REPLACING EXISTING 2-NOTE CHIME
ALL ELECTRICAL WORK MUST BE DONE IN ACCORDANCE WITH LOCAL AND/OR NATIONAL ELECTRICAL CODE		Ground		OPTIONAL: 2 or 3 chimes can be connected to a single transformer. 2 chimes require
AS APPLICABLE.
		120 VAC		transformer Model C909 or C907. 3 chimes require transformer Model C907.
TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING, WIRING, OR SERVICING THIS PRODUCT.
1.	Hold chime mechanism against wall and mark four (4) mounting holes.
2.	Drill 3/16” holes where marked and tap in wall anchors from parts bag.
3.	Bring wiring through access hole(s) in chime mechanism backplate.									Lighted or
4.	Attach chime mechanism to wall with screws from parts bag. Tighten screws securely.									Unlighted Buttons
			16 VAC				Front	Side	Rear
5.	Connect wires to appropriate terminals. Refer to Figure 1 for new construction or Figure 2 if replacing an existing
			Transformer
	2-note chime. Install two (2) alkaline 9-volt batteries, if appropriate for your application.
6.	Hang chime tubes from mechanism as shown in (Figure 3).			1	2	3	F	S	R	NOT USED
7.	Turn on power at service entrance. Make sure pushbuttons operate chime properly. (Adjust switch on circuit
		9V	9V
	board for 4 or 8 chime tones at front door. Side and rear doors will have 1 chime tone each.)
8.	Adjust chime volume with stem on circuit board assembly. If plunger(s) fail to strike tube(s), move tube(s) one			Volume Control						(Figure 2)
	notch closer. If plunger(s) strike a double tone, move tube(s) one notch out.	Requires Two
		9-volt Batteries
9.	Hook cover over chime mechanism.
DO NOT OIL CHIME PLUNGERS.
Oil will cause them to stick during operation. If plungers fail to operate freely due to accumulation of dust, cooking

grease, etc., clean with a non-flammable cleaning solvent which will evaporate, leaving a dry surface.					BATTERY
SPECIAL MOUNTING INSTRUCTIONS FOR MODEL LA500K DOOR CHIME				TUBE
					HOLDERS
Model LA500K may be surface-mounted or recessed into the wall.				HANGER VOLUME	WIRING
SURFACE-MOUNTED				CONTROL	ACCESS
					HOLE
1.	Remove chime mechanism from wood case.
2.	Remove and discard shipping panel from top rear of wood case.
3.	Mount and wire chime mechanism. (Refer to steps 1-5, above.)	14½”
4.	Hang wood case from chime mechanism.					MOUNTING
5.	Install chime tubes. (Refer to steps 6-8, above.)		MOUNTING
						HOLES
6.	Install face plate.		FRAME
RECESSED-MOUNTED		12”	SHIPPING PANEL	CHIME
1.	Cut out a 10-1/2” wide by 59-1/8” high hole in wall centered			TUBE
	between two wall studs.

2.	Make two mounting frames from 2 x 4’s (Figure 4).
3.	Nail mounting frames to wall studs flush with top and bottom of	(Figure 4)
	cut-out (Figure 5).
4.	Bring wiring through access hole(s) in shipping panel.
5.	Attach wood case to mounting frames using black screws and					MOUNTING
	washers (Figure 5).
						FRAME
6.	Bring wiring through access hole(s) in chime mechanism back plate.
			FACEP	LAT	E
7.	Locate four (4) pilot holes in shipping panel and attach chime mechanism using screws from parts bag.
8.	Install chime tubes. (Refer to steps 6-8, above.)
9.	Install face plate.

One Year Limited Warranty
WARRANTY OWNER: Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in
materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.	WOOD
During this one year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be
defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS,	CASE	(Figure 5)			(Figure 3)
service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than
DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and
by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation
on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
Date of Installation			IF YOU NEED ASSISTANCE OR SERVICE - CONTACT:
Builder or Installer			Broan-NuTone LLC	Hartford, Wisconsin www.nutone.com	888-336-3948
Model No. and Product Description			Broan-NuTone Canada	Mississauga, Ontario www.nutone.ca	877-896-1119
					Rev. 08/2007

CARILLON DE PORTE À QUATRE NOTES

Pour enregistrer ce produit, visitez: www.nutone.ca

VEUILLEZ LIRE CES DIRECTIVES ET LES CONSERVER

PLANIFICATION DE L’INSTALLATION

Ce carillon peut accommoder jusqu’à trois (3) entrées. Les boutons de sonnette branchés à la borne “AVANT” jouent une mélodie à 4 ou 8 notes. Les boutons branchés aux bornes “CÔTÉ” et “ARRIÈRE” jouent des notes simples. Pour jouer successivement les 4 ou 8 notes d’une mélodie, le carillon doit posséder une source d’alimentation constante.

CONSTRUCTIONS NEUVES (Figure 1)

Le transformateur fournit une alimentation constante aux bornes 2 et 3 ainsi qu’aux lumières des boutons de sonnette.

REMPLACEMENT D’UN CARILLON À 2 NOTES (Figure 2)

Deux piles de 9 volts fournissent une alimentation constante au carillon, alors que le transformateur permet d’illuminer les boutons de sonnette.

INSTALLATION

TOUTES LES CONNEXIONS ÉLECTRIQUES DOIVENT ÊTRE CONFORMES AUX CODES ET RÈGLEMENTS MUNICIPAUX EN VIGUEUR OU AU CODE NATIONAL DE L’ÉLECTRICITÉ, LE CAS ÉCHÉANT.

COUPEZ LE COURANT AU PANNEAU ÉLECTRIQUE AVANT D’INSTALLER, DE BRANCHER OU DE RÉPARER CE PRODUIT.

1.Tenez le mécanisme du carillon contre le mur et marquez les quatre (4) trous de fixation.

2.Percez des trous de 4 mm (3/16 po) aux endroits marqués et enfoncez les chevilles d’ancrage se trouvant dans le sac de pièces.

3.Enfilez les fils dans le(s) trou(s) d’accès de la plaque arrière du mécanisme du carillon.

4.Fixez le mécanisme du carillon au mur avec les vis se trouvant dans le sac de pièces. Serrez fermement les vis.

5.Branchez les fils aux bornes appropriées. Consultez la figure 1 dans le cas d’une construction neuve ou la figure 2 s’il s’agit de remplacer un carillon à 2 notes. Installez deux (2) piles alcalines de 9 volts, si cela correspond à votre application.

6.Accrochez les tubes du carillon au mécanisme, tel qu’illustré (Figure 3).

7.Rétablissez le courant sur le panneau d’alimentation électrique. Vérifiez si tous les boutons de sonnette déclenchent correctement le carillon. (Réglez le commutateur du circuit imprimé pour obtenir une mélodie à 4 ou à 8 notes pour la porte avant. Les portes du côté et de l’arrière auront un carillon à une seule note chacune.)

8.Réglez le volume du carillon avec la commande du circuit imprimé. Si le ou les pistons plongeurs ne frappent pas le ou les tubes, rapprochez les tubes d’un cran. Si le ou les pistons plongeurs produisent une note double, éloignez les tubes d’un cran.

9.Replacez le couvercle sur le mécanisme du carillon.

CÂBLAGE RECOMMANDÉ POUR CONSTRUCTION NEUVE

Fil de terre	FACULTATIF : 2 ou 3 carillons peuvent être raccordés à un même transformateur.
120 VCA	Pour 2 carillons, utilisez un transformateur de modèle C909 ou C907. Pour 3 carillons,
	utilisez un transformateur de modèle C907.

Boutons illuminés ou non illuminés

Transformateur				Avant		Côté	Arrière
16 VCA
Piles de	1	2	3	F	S	R	NON UTILISÉ
9 volts non
utilisées	Commande de			OU			(Figure 1)
	Volume			NOTES

REMPLACEMENT D’UN CARILLON À 2 NOTES
Fil de terre	FACULTATIF : 2 ou 3 carillons peuvent être raccordés à un même
	transformateur. Pour 2 carillons, utilisez un transformateur de modèle C909
120 VCA	ou C907. Pour 3 carillons, utilisez un transformateur de modèle C907.

Boutons illuminés ou non illuminés

Transformateur					Avant		Côté	Arrière
	16 VCA
		1	2	3	F	S	R	NON UTILISÉ
9 V	9 V
					OU
		Commande de			NOTES			(Figure 2)
Exige deux		Volume
piles de 9 volts

NE HUILEZ PAS LES PISTONS PLONGEURS DU CARILLON.

L’huile entraînera leur collage lors du fonctionnement. Si les pistons plongeurs ne fonctionnent pas librement en raison d’une accumulation de poussière, de graisse de cuisson, etc., nettoyez-les avec un solvant ininflammable qui s’évapore, laissant la surface sèche.