Maytag MPE-33R Minimum Clearances to COMBUS- Tibles, Pre-Installation, Electrical Connections

Page 5

FIREPLACE SPECIFICATIONS

Cat. No. H3427

Model: MPE-33R

Description: Merit Plus Electric Fireplace, 33” Radiant

Shipping Weight: 81 lb.'s (36.75 KG) Packaging:

41” x 17 3/4” x 33 1/2”

(1040 mm x 451 mm x 850 mm)

14.1cu. ft.

Power Requirements: (120 Volt, 60 Hz.)

Rated Wattage - 1600 Watts Amperage - 13.33 Amps

(240 Volt, 60 Hz.)

Rated Wattage - 3000 Watts Amperage - 12.5 Amps

Blower CFM: 83 CFM

(120 V): 5,461 BTU/HR

(240 V): 10,239 BTU/HR

MINIMUM CLEARANCES TO COMBUS- TIBLES

This appliance is an electric fireplace designed to be framed in with combustible materials (up to the edge of the appliance). A drywall lip at the top of the fireplace and 4 nailing flanges on the sides of the appliance is provided to facilitate installation.

 

Clearances

 

 

 

Sides

 

0 inches - 0 mm

Floor

 

0 inches - 0 mm

Top

 

0 inches - 0 mm

Table 2

 

 

 

 

 

Mantel Clearance: Combustible and Non-com- bustible mantels may be installed at any height above the top of the face of fireplace.

Hearth Protection: A hearth is not mandatory, but it is recommended for aesthetic purposes. Secure the hearth extension to the floor to prevent possible shifting. Do no block the air- flow beneath the appliance (read the following WARNING).

WARNING

This appliance is mounted on rubber feet to ensure adequate air circulation beneath fireplace. Do not block airflow at the bottom air intakes.

IMPORTANT

Cold climate installation recom- mendation: when installing this fireplace against a non-insulated exterior wall or chase, it is mandatory that the outer walls be insulated to conform to appli- cable insulation codes.

WARNING

To prevent contact with sag- ging or loose insulation, the appliance must not be installed againstvaporbarriersorexposed insulation. Localized overheat- ing could occur and a fire could result. Insulation and a vapor barrier should be placed a minimum of 2 inches from the appliance.

PRE-INSTALLATION

Before You Start

Check appliance for any concealed damage.

DETAILED INSTALLATION STEPS

1.Complete the framing opening to the dimen- sions specified in Figure 2.

2.Prepare the connections to power source: 120 Volt Connections - Locate the power cord on the left side of the unit and connect it to the outlet installed during the framing (see Figure 2). Verify that the power to the receptacle is off.

Hard wired installation:

Ensure that there is a minimum of 8" of the service cable for connection to the junction box on the fireplace.

-Loosen four screws to remove the junction box cover plate.

-Disconnect and remove the 120 Volt power cord from the fireplace wires.

-Position the fireplace into the framed-in opening. Attach fireplace to frame using nailing flanges provided.

-Complete the wiring to the fireplace as shown on Page 10.

-Place all wire connectors inside the junction box.

-Attach junction box cover plate with four screws.

240 Volt Connections - Ensure that there is a minimum of 8" of the service cable for connection to the junction box on the fireplace.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

-Loosen four screws to remove the junction box cover plate.

-Disconnect and remove the 120 Volt power cord from the fireplace wires.

-Position the fireplace into the framed-in opening. Attach fireplace to frame using nailing flanges provided.

-Complete the wiring to the fireplace as shown on Page 11.

-Place all wire connectors inside the junc- tion box.

-Attach junction box cover plate with four screws.

The fireplace wires L1, L2, N, N1, N2 and G are attached to the rear of the junction box cable clamp for easy access.

3.Wire a dedicated, properly fused circuit with an Amp rating for the appropriate voltage (120 V - 15 Amps or 240 V - 20 Amps). A dedicated circuit is required to prevent overloading a house circuit in cases of having multiple appliances on the same circuit. Use an outlet that is protected by a ground fault circuit interrupter where required by electrical code.

4.(If applicable) Make wall mount wall switch or wall thermostat connections as outlined on Pages 11 & 12.

5.Perform a function test. See Manual Control Panel Operation on Page 6 and Remote Control Operation on Page 7.

ELECTRICAL CONNECTIONS

Refer to the electrical diagrams on Pages 10 to 14.

WARNING

Electrical wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to individuals.

IMPORTANT

Any electrical re-wiring of this appliance must be done by a qualified electrician.

WARNING

Do not use this fireplace if any part of it has been underwater. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Report # C1482763 Electric Fireplace 850,032M REV. B 06/2006Congratulations Table of ContentsGeneral Information Power Supply Wire SpecificationsLocating Your Merit Plus Electric Fireplace Tools and Building Supplies Normally RequiredFireplace Specifications Framing SpecificationsLeft Side Right SideDetailed Installation Steps PRE-INSTALLATIONMinimum Clearances to COMBUS- Tibles Electrical ConnectionsFinal Finishing Main Power On/Off rear most switchBREAK-IN Period Manual Control PanelRemote Control Operation Brick Panel Removal Procedure MaintenanceHEATER/BLOWER Replacement PROCE- Dure Replacing Light Bulbs Bulb Replacement ProcedureAcess bulbs as follows Ember BedWiring 120 Volt Wiring Diagram 120 VoltGround 120 V 1600 WGround Main Power Inside Outside Wall Thermostat & Wall Switch Wiring DiagramsOptional kits, see Inside OutsideWall Thermostat Wall Thermostat Wiring 24 VACBlack White White Left Side FireplaceRed Wire the wall switch prior to installing the fireplaceWall Switch Wiring 24 VAC WHO Performs Corrective Action Causes TroubleshootingDescription Replacement PartsMPE-33R CAT. no125 Replacement Parts Component Diagrams MPE-33RAccessory Components Page 850,032M REV. B 06/2006

MPE-33R specifications

The Maytag MPE-33R is a high-performance refrigerator designed to meet the needs of modern households while prioritizing efficiency and durability. This model stands out with its sleek and timeless design, making it a stylish addition to any kitchen. It offers an array of features that ensure optimal food storage and organization.

One of the key highlights of the MPE-33R is its spacious interior. With a total capacity of 33 cubic feet, it provides ample room for all your groceries, including large items such as pizza boxes and bulk purchases. The customizable storage solutions include adjustable shelves, gallon door bins, and crisper drawers designed to keep fruits and vegetables fresh longer.

The refrigerator incorporates advanced cooling technologies, such as the PowerCold feature, which quickly restores the temperature in the fridge and freezer compartments after opening the doors. This ensures that your food stays at the ideal temperature, preventing spoilage and maintaining freshness. Additionally, the unit employs a Dual Cool System that utilizes separate cooling systems for the refrigerator and freezer compartments, ensuring that odors are not transferred between the two spaces and maximizing food preservation.

Another highlight of the Maytag MPE-33R is its fingerprint-resistant stainless steel finish, which makes it easier to maintain a clean appearance while preventing smudges and fingerprints—a valuable feature for busy households. The appliance also features LED lighting that brightens the interior without consuming significant energy, allowing for better visibility of stored items.

For energy-conscious consumers, the Maytag MPE-33R is Energy Star certified, signifying that it meets strict energy efficiency guidelines set by the Environmental Protection Agency. This feature not only helps reduce utility bills but also promotes a more sustainable lifestyle.

Overall, the Maytag MPE-33R refrigerator is an excellent choice for families seeking a reliable, spacious, and efficient appliance. With its smart features, customizable storage options, and sleek design, it delivers convenience and peace of mind for all your food preservation needs. Whether you're stocking up for a big family meal or simply keeping everyday essentials on hand, the MPE-33R is built to handle it all.
Top Page Image Contents