Maytag MPE-33R Maintenance, HEATER/BLOWER Replacement PROCE- Dure, Brick Panel Removal Procedure

Page 8

8

MAINTENANCE

This appliance has been designed to provide many years of trouble-free service. The com- ponents that will need to be serviced have been kept to a minimum. Periodic dusting of the fireplace is all that should be required.

CAUTION

Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury.

WARNING

When cleaning the fireplace, the fireplace must be cool.

CLEANINGTHEGLASSENCLOSUREPANEL (OPTIONAL KIT)

Over time the front glass panel may become dirty or dusty. Dust can be removed by lightly rubbing the glass surface with a clean, lint free cloth or paper towel. To remove fingerprints or other marks, use a damp cloth with a good quality household glass cleaner. The front glass panel should be completely dried with a clean, lint free cloth or paper towel.

CAUTION

Do not use abrasive cleaners on the glass panel. Do not spray liquids directly onto any surface of the fireplace.

WARNING

An authorized service represen- tative should perform any other servicing.

CAUTION

Handle glass very carefully to prevent accidental breakage.

HEATER/BLOWER REPLACEMENT PROCE- DURE

1.Turn off power to the fireplace.

2.Let the fireplace completely cool, if it has been operating.

3.Open the screens (remove glass panel enclosure, if applicable).

4.OPTIONAL: To ensure that the brick panel isn't accidentally scratched, you may wish to remove it before proceeding:

Brick Panel Removal Procedure:

a.Remove the 2 screws on the front of the grate. Remove Grate (see Figure 8).

b.Lift out Log / Ember assembly and set aside. Caution: Be careful not to scratch the finish.

c.Remove the top brick panel retaining bracket (see Figure 15). Be very careful to hold the bracket when removing the 2 screws to ensure the bracket doesn't fall.

d.Remove the left and right side brick panel retaining brackets (see Figure 15). Be very careful to hold the bracket when removing. Remove the bottom screw first to avoid the frame falling down after both screws are removed.

TAKE CARE TO HOLD BRICK PANEL IN PLACE TO PREVENT POSSIBLE DAMAGE.

Suggestion: Slide the screens toward the middle of the fireplace for easier access to the screws on the sides. Return the screens to the sides before proceeding to instruction e.

e.Tip brick panel forward from the top, just enough to clear screens. Carefully remove brick panel from firebox and set aside in a safe place.

5.Remove the screws which secure the heater blower mounting plate using a phillips screw- driver as follows (see Figures 9 & 10):

a.While using one hand to hold the handle of the heater/blower assembly (see Figure 9), remove the 5 screws which secure the mounting plate. Remove the 4 side screws first (2 on each side). Remove the middle screw that is on the top of the handle last.

b.Slowly lower the heater/blower assembly and let it rest on the 2 support chains (1 on each side).

IMPORTANT NOTE: Label all wire loca- tions prior to disconnecting to ensure that wires are reconnected in the correct positions.

6.Replace the heater/blower as follows:

a.Replace the old heater/blower with the new one. Note: when replacing the heater/blower, ensure that all the wires on the heater are correct, otherwise the heater will not function properly.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

b. Turn the power and heater switches on and check for proper operation.

c. Turn off power to the fireplace.

d. Using one hand to hold the handle of the heater/blower assembly, slowly push it back up and line up the holes for the 5 screws. Install the 5 screws to secure the new heater/blower assembly to the mounting plate.

7.(If brick panel was removed) Reverse instructions on Step 4.

8.Reinstall glass panel enclosure, if appli- cable.

Grate

Figure 8

Heater/blower Mounting Plate

Handle

Brick Panel

Remove screws indicated by arrows

Figure 9

Heater/blower Mounting Plate

Be careful not to

damage brick panel

Figure 10

Blower / Heater

Figure 11

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Electric Fireplace 850,032M REV. B 06/2006 Report # C1482763Table of Contents CongratulationsPower Supply Wire Specifications General InformationLocating Your Merit Plus Electric Fireplace Tools and Building Supplies Normally RequiredFraming Specifications Fireplace SpecificationsLeft Side Right SidePRE-INSTALLATION Detailed Installation StepsMinimum Clearances to COMBUS- Tibles Electrical ConnectionsMain Power On/Off rear most switch Final FinishingBREAK-IN Period Manual Control PanelRemote Control Operation Brick Panel Removal Procedure MaintenanceHEATER/BLOWER Replacement PROCE- Dure Bulb Replacement Procedure Replacing Light BulbsAcess bulbs as follows Ember BedWiring Diagram 120 Volt Wiring 120 VoltGround 120 V 1600 WGround Main Power Wall Thermostat & Wall Switch Wiring Diagrams Inside OutsideOptional kits, see Inside OutsideWall Thermostat Wiring 24 VAC Wall ThermostatBlack White White Left Side FireplaceRed Wire the wall switch prior to installing the fireplaceWall Switch Wiring 24 VAC Troubleshooting WHO Performs Corrective Action CausesReplacement Parts DescriptionMPE-33R CAT. noReplacement Parts Component Diagrams MPE-33R 125Accessory Components Page 850,032M REV. B 06/2006

MPE-33R specifications

The Maytag MPE-33R is a high-performance refrigerator designed to meet the needs of modern households while prioritizing efficiency and durability. This model stands out with its sleek and timeless design, making it a stylish addition to any kitchen. It offers an array of features that ensure optimal food storage and organization.

One of the key highlights of the MPE-33R is its spacious interior. With a total capacity of 33 cubic feet, it provides ample room for all your groceries, including large items such as pizza boxes and bulk purchases. The customizable storage solutions include adjustable shelves, gallon door bins, and crisper drawers designed to keep fruits and vegetables fresh longer.

The refrigerator incorporates advanced cooling technologies, such as the PowerCold feature, which quickly restores the temperature in the fridge and freezer compartments after opening the doors. This ensures that your food stays at the ideal temperature, preventing spoilage and maintaining freshness. Additionally, the unit employs a Dual Cool System that utilizes separate cooling systems for the refrigerator and freezer compartments, ensuring that odors are not transferred between the two spaces and maximizing food preservation.

Another highlight of the Maytag MPE-33R is its fingerprint-resistant stainless steel finish, which makes it easier to maintain a clean appearance while preventing smudges and fingerprints—a valuable feature for busy households. The appliance also features LED lighting that brightens the interior without consuming significant energy, allowing for better visibility of stored items.

For energy-conscious consumers, the Maytag MPE-33R is Energy Star certified, signifying that it meets strict energy efficiency guidelines set by the Environmental Protection Agency. This feature not only helps reduce utility bills but also promotes a more sustainable lifestyle.

Overall, the Maytag MPE-33R refrigerator is an excellent choice for families seeking a reliable, spacious, and efficient appliance. With its smart features, customizable storage options, and sleek design, it delivers convenience and peace of mind for all your food preservation needs. Whether you're stocking up for a big family meal or simply keeping everyday essentials on hand, the MPE-33R is built to handle it all.
Top Page Image Contents