Maytag HRE3940L, HRE3966T Instructions for Installation cont’d, Locating The New Water Heater

Page 9

Instructions for Installation (cont’d)

Locating The New Water Heater

You should carefully choose an indoor location for the new water heater, because the placement is a very important con- sideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not intended for outdoor installation.

Whether replacing an old water heater or putting the water heater in a new location, the following critical points must be observed.

1.The location selected should be indoors as close to and as centralized with the water piping system as possible. This water heater, as well as all water heaters, will eventually leak. Do not install without adequate drainage provisions where water flow will cause damage.

CAUTION

WATER HEATERS EVENTUALLY LEAK: Installation of the water heater must be accomplished in such a manner that if the tank or any connections should leak, the flow of water will not cause damage to the structure. For this reason, it is not advisable to install the water heater in an attic or upper floor. When such locations cannot be avoided, a suitable drain pan should be installed under the water heater. Drain pans are available at your local hardware store. Such a drain pan must have a minimum diameter of at least 13⁄4 inches greater than the water heater diameter and must be piped to an adequate drain.

CAUTION

INSTALLATION IN RESIDENTIAL GARAGES: The water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle.

2.The location selection must provide adequate clearances for servicing and proper operation of the water heater.

Typical Installation

CHECK ALL CONNECTIONS FOR LEAKS.

CONSULT THE LOCAL UTILITY COMPANY TO EXAM- INE INSTALLATION FOR PROPRIETY AND SAFETY.

* WARNING

HOTTER WATER CAN SCALD: Water heaters are intended to produce hot water. Water heated to a temperature which will satisfy clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, the infirm, or physically/mentally handi- capped. If anyone using hot water in your home fits into one of these groups or if there is a local code or state law requiring a certain temperature water at the hot water tap, then you must take special pre- cautions. In addition to using the lowest possible temperature setting that satisfies your hot water needs, a means such as a mixing valve, should be used at the hot water taps used by these people or at the water heater. Mixing valves are available at plumbing supply or hardware stores. Follow manu- facturers instructions for installation of the valves. Before changing the factory setting on the thermo- stat, read the “Temperature Regulation” section in this manual.

VACUUM RELIEF REQUIRED BY SOME CODES (REFER TO LOCAL CODES)

SHUTOFF VALVE

HOT

WATERCOLD WATER INLET

OUTLET

 

ELBOW

 

 

 

UNION

 

UNION

3/4″ THREADED

TEMPEREDCONNECTORS WATER

OUTLET *MIXING VALVE

ELECTRICAL

 

 

JUNCTION BOX

 

 

 

 

TEMPERATURE-

 

 

 

 

 

PRESSURE

ACCESS COVER

 

RELIEF VALVE

 

 

 

 

DISCHARGE

PIPE

(Do not cap or plug)

ACCESS COVER

DRAIN VALVE

6″ AIR GAP

TO SUITABLE DRAIN

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Electric Water Heater USER’S Guide DEATH, Serious Bodily INJURY, or Property Damage Safety InstructionsSafety Instructions cont’d Table of Contents Customer Information Minimum Wire Size Gauge Product SpecificationsAccessories Accessories and Tools NeededAdditional Tools Needed When Sweat Soldering ToolsRemoving the Old Water Heater Instructions for InstallationTypical Installation Instructions for Installation cont’dLocating The New Water Heater Check ALL Connections for LeaksOUS Bodily INJURY, or Property Damage Convertible Lower ElementValve and Pipe Insulation Water Piping″ AIR GAP Floor Drain Temperature-Pressure Relief ValveConverting the Lower Element Filling the Water HeaterConverting the Lower Element cont’d OUS Bodily INJURY, or Property Damage Standard Wiring for Wiring DiagramsLength in any ground return path does not exceed 6 feet WiringModel Rating Plate Installation ChecklistTemperature Regulation Service and MaintenanceTemperature Settings ThermostatsThermostat Adjustments Service and Maintenance cont’dTemperature-Pressure Relief Valve Operation Anode Rod InspectionDraining Thermostat Removal/ReplacementThermostat Removal cont’d Element Cleaning ReplacementService and Maintenance cont’d Element Cleaning Replacement cont’d Drain Valve Washer ReplacementService Troubleshooting Start Up ConditionsOperational Conditions Not Enough or no HOT Water Troubleshooting cont’dLY INJURY, or Property Damage Leakage CheckpointsMaytag Electric Water Heaters Model Numbers Repair Parts ListGallon Repair Parts List cont’dKEY Part Description Part NumbersHRE2940L Element Gasket 66001053 Primary Anode 66001723 HRE2950S HRE3950S HRE2950T HRE3950T HRE2966T HRE3966T ETC2X Page Full ONE Year Warranty Warranty

HRE3950S, HRE2940S, HRE3930T, HRE2966T, HRE3940L specifications

The Maytag ranges HRE2950S, HRE2940S, HRE2940T, HRE3940S, and HRE3930T stand out in the crowded appliance market, known for their robust design and innovative features. Each model is designed with the home chef in mind, ensuring that meal preparation is both efficient and enjoyable.

One of the primary features across these models is the durable cast-iron grates that provide a professional cooking experience. They offer excellent heat retention and stability for pots and pans, allowing for optimal heat distribution when cooking. The grates are also easy to clean, making maintenance a breeze.

Another key technology integrated into these ranges is the precise temperature control, which comes from the advanced direct flame technology. This ensures that cooking temperatures can be accurately maintained, enabling recipes to be executed flawlessly. This is particularly beneficial for baking and searing, where precision is crucial.

The HRE2950S and HRE2940S models come equipped with a powerful 15,000 BTU burner, perfect for boiling and frying, while the HRE2940T model features a high-efficiency burner designed to save energy without sacrificing performance. These powerful burners allow for a range of cooking methods, from fast boiling to slow simmering.

Cooking companions in these ranges include a self-cleaning oven feature, which takes the hassle out of cleaning after a long day of cooking. The self-cleaning cycle uses high temperatures to burn off debris and food residue, resulting in a clean oven without scrubbing or harsh chemicals.

The HRE3940S and HRE3930T models are especially notable for their spacious oven capacity, which allows multiple dishes to be cooked simultaneously. This feature is ideal for entertaining or large family meals, ensuring ample room for various culinary creations.

In addition to functionality, aesthetic appeal is crucial. These Maytag ranges boast a sleek, modern design with a stainless-steel finish that adds a touch of elegance to any kitchen. The ergonomic knobs and handles complement the professional appearance, making these ranges as attractive as they are efficient.

With a commitment to durability, performance, and ease of use, the Maytag HRE2950S, HRE2940S, HRE2940T, HRE3940S, and HRE3930T are perfect for aspiring chefs and seasoned cooks alike. These ranges combine innovative features with practical functionality, making them a valuable addition to any household kitchen.
Top Page Image Contents