Venting

•Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

•To insure complete filling of the tank, allow air to exit by opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the water heater and the piping.

•Check all water piping and connections for leaks. Repair as needed.

VENT DAMPERS - Any vent damper, whether it is operated thermally or otherwise must be removed if its use inhibits proper drafting of the water heater.

Thermally Operated Vent Dampers: Gas-fired water heaters having thermal efficiency in excess of 80% may produce a relatively low flue gas temperature. Such temperatures may not be high enough to properly open thermally operated vent dampers. This would cause spillage of the flue gases and may cause carbon monoxide poisoning.

Vent dampers must bear evidence of certification as complying with the current edition of the American National Standard ANSI Z21.68 (ANSI Z21.66 & 67, respectively, cover electrically and mechanically actuated vent dampers). Before installation of any vent damper, consult your Maytag Customer Service Center at 1-800-788-8899or the local gas supplier for further information.

For replacement heater installations where using pre-existing venting, venting must be inspected for obstructions and if deterioration is present venting must be replaced.

proper venting for your water heater from the vent tables in the current edition of the National Fuel Gas Code ANSI Z223.1/ NFPA 54.

Periodically check the venting system for signs of obstruction or deterioration and replace if needed.

The combustion and ventilation air flow must not be obstructed.

The water heater with draft hood installed must be connected to a chimney or listed vent pipe system, which terminates to the outdoors. Never operate the water heater unless it is vented to the outdoors and has adequate air supply to avoid risks of improper operation, explosion or asphyxiation.

•For proper draft hood attachment, the draft hood legs may be angled slightly inward.

•Place the draft hood legs in the receiving holes on the top of the water heater. The legs will snap in the holes to give a tight fit. Secure two legs to top with sheet metal screws.

•Place the vent pipe over the draft hood. With the vent pipe in position, drill a small hole through both the vent pipe and draft hood. Secure them together with a sheet metal screw, see Figure 18.

Obstructed or deteriorated vent systems may present serious health risk or asphyxiation.

To insure proper venting of this gas-fired water heater, the correct vent pipe diameter must be utilized. Any additions or deletions of other gas appliances on a common vent with this water heater may adversely affect the operation of the water heater. Consult your Maytag Service Center at 1-800-788- 8899 or gas supplier if any such changes are planned.

For proper venting in certain installations, a larger diameter vent pipe may be necessary. Consult your Maytag Customer Service Center or gas supplier to aid you in determining the

FIGURE18.

The vent pipe from the water heater must be no less than the diameter of the draft hood outlet on the water heater and must slope upward at least 1/4 inch per linear foot (21 mm per meter), see Figure 19.

FIGURE19.

All vent gases must be completely vented to the outdoors of the structure (dwelling). Install only the draft hood provided with the new water heater and no other draft hood.

Vent pipes must be secured at each joint with sheet metal screws.

C3 specifications

The Maytag C3 is a cutting-edge kitchen appliance that has gained significant recognition for its innovative features and exceptional performance. Designed with the modern home chef in mind, the C3 epitomizes convenience, efficiency, and style.

One of the standout features of the Maytag C3 is its advanced cooking technology. The appliance utilizes a powerful convection cooking system that ensures even heat distribution, allowing for perfectly cooked meals every time. This technology not only improves the quality of cooking but also enhances the appliance's energy efficiency, making it an eco-friendly choice for households.

The Maytag C3 also boasts a user-friendly interface, equipped with a digital touchscreen control panel that simplifies the cooking process. This intuitive design allows users to easily browse through a variety of pre-programmed cooking settings, ensuring you have the right option for every dish you prepare. The appliance supports smart cooking, connecting to a mobile app that provides step-by-step guidance, recipe suggestions, and remote control functions.

In terms of capacity, the C3 is designed to accommodate large meals with ease. The spacious interior allows you to cook multiple dishes simultaneously, making it ideal for family gatherings or dinner parties. Additionally, the appliance is equipped with multiple cooking modes, including bake, broil, grilling, and roasting, giving users the versatility they need in the kitchen.

Another notable characteristic of the Maytag C3 is its durable construction. Built from high-quality materials, this appliance is designed to withstand the rigors of daily use. The stainless steel finish not only adds a touch of elegance to your kitchen but also makes cleaning a breeze. The removable racks and trays are dishwasher-safe, ensuring that upkeep is minimal.

Safety is also a priority with the Maytag C3. The appliance features a child lock system, preventing accidental operation, which is particularly valuable for families with young children.

In summary, the Maytag C3 is a remarkable kitchen appliance that combines advanced cooking technology with user-friendly features. Its spacious capacity, versatility in cooking modes, and durable construction make it an excellent choice for anyone looking to elevate their home cooking experience. Whether you are a seasoned chef or a novice in the kitchen, the Maytag C3 is designed to meet your culinary needs with style and efficiency.