Multiquip MQD2H manual Setup, Handle Installation

Page 16

SETUP

Handle Installation

The MQ-D2H/D3H diaphragm pumps are completely assembled except for the steering handle. Attach the steering handle to the pump base as shown in Figure 6.

GEAR

BOX

HANDLE

BOLT

WASHER

PUMP BASE

Figure 6. Handle Installation

Before Starting:

CAUTION - General Safety Precautions

NEVER operate the pump in a confined area or enclosed area structure that does not provide ample free flow of air.

ALWAYSwear approved eye and hearing protection before operating the pump.

Before Starting

1.Read safety instructions at the beginning of manual.

2.Place pump as near to water as possible,onafirmflat,levelsurface.

WARNING - Fill Cap

DO NOT open fill cap if pump is hot! Water inside may be under pressure.

Hoses and Clamps

1.Check that all hoses are securely attached to the pump. Make certain suction hose (Figure 2) does not have any air leakage. Use teflon tape or pipe dope on NPT threads.

2.Remember suction hoses must be rigid enough not to collapse when the pump is in operation.

3.Check that the discharge hose (Figure 2) is not restricted. Place hose so that it lays as straight as it is possible on the ground. Remove any twists or sharp bends from hose which may block the flow of water.

Suction and discharge hoses are

NOTE available from Multiquip. Contact your nearest dealer for more information.

4.The discharge hose is usually a collapsible (thin-walled) hose, however if a thin-walled discharge hose is not avail- able, a rigid suction hose can be substituted in its place.

5.Make sure the suction strainer (Figure 2) is clean and securely attached to the water end of the suction hose. The strainer is designed to protect the pump by preventing large objects from being pulled into the pump.

CAUTION - Transmission Fluid

Transmission fluid needs to be added prior to operation.

PAGE 16 — MQD2H/3H DIAPHRAGM PUMPS — OPERATION AND PARTS MANUAL — REV. #6 (10/27/11)

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Models MQD2H MQD3H Proposition 65 Warning Page MQ-D2H/D3H Gasoline Powered Diaphragm Pumps Table of ContentsParts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesGeneral Safety Pump Safety Lifting Safety Specifications Pump SpecificationsMQ-D2H DimensionsMQ-D3H General Information ApplicationComponents Contact your nearest MultiquipBasic Engine Initial ServicingInspection InspectionSetup Handle InstallationMechanical seal to prevent water Operation Starting the Engine Honda engineNormal Shutdown Maintenance Pump Vacuum TestAltitude. See Tables 4 Rotation of Suction and Discharge Ports Seized Plunger Engine Maintenance Schedule Daily Preparation for LONG-TERM Storage Pump StorageTroubleshooting Engine TroubleshootingEngine Troubleshooting Pump Troubleshooting Explanation of Code in Remarks Column Xxxxx only Not Used onQty Description Name Plate and Decals Assy Nameplate and Decals AssyDECAL, Grease Monthly DECAL, MQ LogoMQD2H Waterbox and Flap Valve Assy Waterbox and Flap Valve Assy -INCHSuction Priming Chamber Priming PlugPrimimg Plug Gasket Flapper Valve AssyMQD2H -PUMP Assy Pump Assy -INCHInternal Retaining Ring 1-1/2 Plunger ARMCrank OIL SealHANDLE, Engine and Wheel Assy -INCH MQD2H -HANDLE, ENGINE, and Wheel Assy MQD3H -WATERBOX and Flap Valve Assy 212300001 MQD3H Pump Assy Pump Assy -INCH170400200 MQD3H HANDLE, ENGINE, and Wheel Assy MQD3H HANDLE, ENGINE, and Wheel Assy Engine Mount TBD BoltHonda GX120K1QX2 Engine AIR Cleaner Assy AIR Cleaner AssyGROMMET, AIR Cleaner COLLAR, AIR CleanerCollar B, AIR Cleaner GASKET, ElbowHonda GX120K1QX2 Engine Camshaft Assy Camshaft AssySPRING, Weight Return ROD, PushARM, Valve Rocker LIFTER, ValveHonda GX120K1QX2 Engine Carburetor Assy Carburetor AssyPLATE, Lever Setting Gasket SETValve SET, Float Float SETHonda GX120K1QX2 Engine Control Assy Control AssyARM, Governor ROD, GovernorSPRING, Governor SPRING, Throttle ReturnHonda GX120K1QX2 Engine Crankcase Cover Assy Crankcase Cover AssyGASKET, Case Cover GASKET, OIL Filler CAPBEARING, Radial Ball PIN A, DowelHonda GX120K1QX2 Engine Crankshaft Assy Crankshaft AssyCRANKSHAFT, H-TYPE Honda GX120K1QX2 Engine Cylinder Barrel Assy Cylinder Barrel AssyWEIGHT, Governor PIN, Governor WeightSLIDER, Governor SHAFT, Governor ARMHonda GX120K1QX2 Engine Cylinder Head Assy Cylinder Head AssyGUIDE, Valve OS Optional CLIP, Valve GuideGASKET, Cylinder Head COVER, HeadHonda GX120K1QX2 Engine FAN Cover Assy FAN Cover AssyGROMMET, Adjusting Cover WIRE, Stop Switch 370MMCOVER, FAN *NH1* Black PLATE, Side OIL AlertHonda GX120K1QX2 Engine Flywheel Assy Flywheel AssyFAN, Cooling PULLEY, StarterFlywheel NUT, Special 14MMHonda GX120K1QX2 Engine Fuel Tank Assy Fuel Tank AssyRUBBER, Supporter 107MM JOINT, Fuel TankTANK, Fuel *NH1* Black GASKET, Fuel Filler CAPHonda GX120K1QX2 Engine Ignition Coil Assy Ignition Coil AssyCoil ASSEMBLY, Ignition Honda GX120K1QX2 Engine Muffler Assy Muffler AssyMuffler PROTECTOR, MufflerGASKET, Muffler SCREW, TappingHonda GX120K1QX2 Engine Piston Assy Piston AssyBOLT, Connecting ROD Ring SET, Piston StandardPISTON, Standard PISTON, OSHonda GX120K1QX2 Engine Recoil Starter Assy Recoil Starter AssySCREW, Setting REEL, Recoil StarterRATCHET, Starter GUIDE, RatchetHonda GX120K1QX2 Engine Gasket KIT Assy Gasket KIT Assy06111ZH7405 Honda GX120K1QX2 Engine Labels Assy Labels AssyEmblem LABEL, CautionMARK, Choke MARK, OIL Alert ETerms and Condition of Sale Parts Freight PolicyPage HERE’S HOW to GET Help

MQD2H specifications

The Multiquip MQD2H is a versatile and robust diesel-powered generator designed to cater to a wide range of applications, making it a staple for construction sites, emergency backup, and outdoor events. Engineered with advanced technologies, this generator is built to deliver reliable power and withstand challenging environments.

At the heart of the MQD2H is a powerful, fuel-efficient diesel engine that ensures long operational hours with minimal downtime. This efficiency is crucial for projects requiring continuous power supply. Equipped with a large fuel tank, the MQD2H can operate for extended periods without the need for frequent refueling, enhancing productivity on the job site.

One of the standout features of the MQD2H is its robust construction. The generator is housed in a durable frame that protects it from physical damage and harsh weather conditions. Its compact design allows for easy transportation and maneuverability, making it ideal for various locations. Additionally, the generator is equipped with advanced soundproofing technology, reducing operational noise levels and making it suitable for use in noise-sensitive environments.

The MQD2H is designed with user convenience in mind. It features an intuitive control panel that provides easy access to vital operational information, allowing users to monitor the generator's performance at a glance. The control panel includes circuit breakers, start/stop switches, and hour meters, ensuring that operators have full control over the generator’s functionality.

Safety is also a priority with the Multiquip MQD2H. The generator incorporates automatic shutdown features for low oil pressure and high engine temperature, protecting the unit from potential damage. This built-in safety mechanism provides peace of mind for operators, knowing that the generator is safeguarded against operational hazards.

Furthermore, the MQD2H complies with emission regulations, making it an environmentally friendly choice among generators. The design includes technologies that minimize harmful emissions without compromising power output, adhering to industry standards and promoting cleaner operation.

In conclusion, the Multiquip MQD2H is a reliable, durable, and efficient generator ideal for a multitude of applications. With its powerful diesel engine, user-friendly controls, enhanced safety features, and commitment to environmental sustainability, it stands out as a top choice for professionals seeking dependable power solutions in demanding conditions.
Top Page Image Contents