Keating Of Chicago 055173 installation instructions Operation #2 Re-Assembly

Flexible Tubing to Hard Piping Installation

Instructions – for Motor/Pump Part# 055173 Continued

Page 2 of 2

Operation #2 Re-Assembly

Notes:
			Your Kit Includes (items with * may not be included):
1. Remove filter tub from motor/pump housing assembly and set
aside. On 18, 20 and 24 models only, remove pipe nipple 3/8”			Item	Part #	Qty	Description
NPT x 1” and discard. Replace with pipe nipple 3/8” NPT x 1-			A	---------	-	------------------------
			*B	056990	1	Pipe Nipple 3/8 NPT 1-1/2 SS-304
1/2” (item B). See view A for proper dimensions from back of
			C	056907	1	Bracket Ass’y Haight Baker Pump
sump to front of quick connect. On 14” filter tub, see view A
			D	020101	8	Nut 5/16 Hex Head Serrated Flang
for proper dimesions from back of sump to front of quick dis-
			E	017142	4	Screw 5/16-18 x 3/4 Hex Head
connect. Place the filter tub into the filter cart assembly.			F	015227	2	Nut 1/4” Acorn S/S
Release the filter tub away from the pump housing as shown			G	004611	4	Screw #10 x 3/8 Sheet Metal Pan HD.
in side view. Turn the entire assembly upside down as shown			*I	037672	A/R	Sealant Locktite 262 (.017 oz.)
in view B. This step is critical to insure proper alignment			J	056765	8	Washer Flat 7/16” ID x 1.00 OD x .078 THK.
between the motor housing quick connect and the filter tub			K	017481	4	Screw 5/16 -18 x 1-3/4 Hex HD SS
			L	X	1	Reinforcement Bracket
quick connect. Use table or bench, making sure the
			M	015158	2	Acorn Nut 5/16-18 SS
motor/pump housing is off of the table/bench.
			N	052733	2	Washer 11/32 ID x 3/4 OD
CAUTION: IF FILTER ASSEMBLY IS PLACED UPSIDE DOWN
			O	000290	2	Washer, Lock 5/16” Spilt
ON A TABLE OR BENCH, MAKE SURE UNIT IS SECURE, SO
AS NOT TO SLIDE OFF TABLE/BENCH.			THIS TIME. Play must be present for proper alignment of
2. Slide item C into position to connect the compression fitting on			pump housing connect and filter tub quick connect. Slide the
			filter tub assembly forward until the quick connects are
the pump’s 90° fitting. DO NOT TIGHTEN COMPRESSION
			engaged. Tighten items D and E completely. Tighten compres-
FITTING AT THIS TIME. Attach item C, to the pump housing
			sion on item C. Remove (2) bolts and washers “K” and add
with items D and E. DO NOT TIGHTEN COMPLETELY AT
					reinforcement bracket “L.” Use longer (2) bolts pro-
		Bottom View			vided and discard old ones. For 20 and 24 models,
Pump Mount Cover	Mount Reinforcement				add items D and K to reinforcement bracket and
G See Note #4		Bracket as Shown			tighten until snug on motor mount housing assem-
			L
					bly (See Bottom View).
Motor Mount Housing Assembly		Bolts
	Must Be				3. Attach filter tub pull rod handle using item
	Flush Not
					F and I.
Filter Tub Assembly		Tight

4. Attach the pump mount covers using item G.

		Filter Cart Frame Assembly				C
						K&D Bolts Only
						for Models 20”
	L	Filter Tub Connected			J&I See	and 24” See
			Side View			Note #2
	See Note #2				Note #5
	See Note #1
Filter Tub	K,M,N,O	F&I See		See Note A
					View A
Pull Rod			B
		Note #3

5.	Inspect for spacers between casters and filter
	cart assembly. If none are present, remove
	casters and place item J (2) on the casters
	threaded stem and reassemble using existing
	fasteners and item I.
6.	Carefully turn filter assembly to the upright posi-
	tion. Release the filter tub pull rod and check for
	proper disconnect. Reconnect the filter tub to
	the motor mount housing using handles. If the

See Note #3

D&E

Support Filter Tub As Shown to Remove Any Play Between Tub and Filter Cart.

assemblies do not connect properly, it will be

necessary to verify notes above were followed

correctly.

7. Fill filter tub with oil per users manual, cycle oil

to check for leaks at fittings, correct if needed.

Note A Dimensions

9-5/16” for 14” Filter

11-3/8” for 18” Filter

Filter Tub Disconnected

View B

2-5/8”

12-3/8” for 20” Filter

Table or Bench

Item ‘C’ Detail

14-3/8” for 24” Filter