GE 3200 installation instructions Conduit

Page 14

Installation Instructions

6Use the round knockout at the bottom of the junction box to attach conduit coming from the branch circuit. Remove the knockout,

attach the conduit and bring wires into the junction box. Leave 6″ of wire free at the end of the conduit to allow connections to be made.

Conduit

7If a fuse and fuseholder are to be used, the knockout at the top of the box is for mounting a Buss Fuseholder. Be sure the fuse and fuseholder are of the same rating as the branch circuit. Leadwires at the fuse can be either

soldered in place or attached using UL-listed 1/4″ female (receptacle) crimp connectors.

14

8Reinstall the junction box by engaging the tab at the lower rear, aligning the screw hole at the top and driving the one screw until secure. Be sure that all wire leads are inside the box and not pinched between the box and the chassis. The identified (ribbed) Neutral wire of the cordset MUST be connected to the white Neutral wire of the branch circuit. The green insulated ground wire from the chassis MUST be connected to the branch circuit ground wire.

9Make all wire connections by using appropriate UL-listed electrical connectors and techniques (black to black, white to white and green to green).

10Carefully tuck all wires and connections back inside the junction box. Be sure there are no loose connections or stray uninsulated wires exposed.

11Place the junction box cover in place. Replace the four screws removed earlier and tighten securely.

12Discard the unused portion of the plug and the cordset.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Zoneline Write down the model and serial Before using your Zoneline800.626.2000 Read ALL Safety Information Before Using Replacing an existing unit?Controls on your Zoneline Series onlyEnergy Tip Other Zoneline features To Remove the Room CabinetFreeze Sentinel Fan SwitchAuxiliary Controls Base Pan Care & CleaningOutdoor Coils Room Cabinet and CaseAir Filters Read carefully Replacing an Existing Unit?Zoneline Components Important Electrical Safety-Read CarefullyImportant Notes Do not use an extension cord with this unitHow to Connect 230/208 Volt Electrical SupplyVolt Electrical Supply Steps for preparing cordset for direct connectionConduit Insulated Wall Case Install the Wall Case and the Exterior GrilleRemove the Shipping Tape from the Room Cabinet Install the Unit into the Wall Case Replace the Room CabinetElectric Heat Option-Model 3200 Series only Low Voltage Connectors & Auxiliary ControlsTemperature Limiting All-Time Low Fan Remote Control/Wall Thermostat ClassCentral Desk Control Load Shedding Explanation Things That Are NormalNoise Zoneline Does Not Before You Call For ServiceProblem Possible Causes Cool or Heat as itBurning Odor at Start of Heating Operation Heating OperationPage Parts and Accessories Further ServiceOn-Site Repair Service We’ll be thereWhat Is Covered What Is Not Covered

3200 specifications

The GE 3200 is an advanced control system designed for a wide range of applications, primarily in the power generation sector, including gas and steam turbines. Known for its reliability and flexibility, the GE 3200 boasts several main features that set it apart from other control systems on the market.

One of the key characteristics of the GE 3200 is its modular architecture. This design allows for easy scalability and customization to cater to various operational needs. Whether a facility is operating a single turbine or a fleet of equipment, the system can be tailored to suit specific requirements, making it an ideal choice for both new installations and upgrades to existing plants.

The GE 3200 incorporates state-of-the-art technologies designed to enhance operational efficiency and safety. At the heart of the system is advanced digital signal processing capabilities, which enable real-time monitoring and control of equipment. This technology ensures that any deviation from normal operating parameters is quickly detected, allowing for immediate corrective action to be taken. This proactive approach helps minimize downtime and optimize performance.

Another significant feature of the GE 3200 is its user-friendly interface. The system is equipped with intuitive graphical displays that provide operators with vital information regarding the status of equipment and processes at a glance. This ease of use enhances operational efficiency by allowing staff to quickly assess system performance and respond to issues as they arise.

Moreover, the GE 3200 supports a variety of communication protocols, ensuring seamless integration with a range of devices and control systems. This interoperability is essential for modern power plants where multiple systems need to work together cohesively.

Security is also a top priority for the GE 3200. The system includes robust cybersecurity measures, protecting operational data from unauthorized access and cyber threats. This ongoing commitment to securing industrial control systems is critical in today's digital landscape.

In conclusion, the GE 3200 is a sophisticated control system that integrates advanced technologies with user-friendly features. Its modular design, real-time monitoring capabilities, and robust security measures make it an optimal solution for enhancing the efficiency and safety of power generation operations.
Top Page Image Contents