Before YOU Begin, Electrical Requirements

Installation Instructions

Air Conditioner

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT — Save these

instructions for local inspector’s use.

•IMPORTANT — Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Skill level – Installation of this appliance requires basic mechanical skills.

•Completion time – Approximately 1 hour

•We recommend that two people install this product.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

CAUTION:

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Do not change the plug on the power cord of this air conditioner.

Aluminum house wiring may present special problems—consult a qualified electrician.

ELECTRICAL REQUIREMENTS

Some models require a 115/120-volt a.c., 60 Hz grounded outlet protected with a 15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires.

TOOLS YOU WILL NEED

Phillips head screwdriver

Scissors or knife

Flat-blade screwdriver

Pencil

Level

Ruler or tape measure

Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.

AGM05 specifications

The GE AGM05 is a cutting-edge aircraft engine that represents the pinnacle of engineering in the field of aviation technology. Designed for the next generation of commercial jetliners, the AGM05 boasts an array of features, technologies, and characteristics that make it a standout in the competitive aerospace market.

One of the main features of the AGM05 is its advanced materials composition. Utilizing lightweight composites and durable alloys, the engine offers significant weight savings without compromising structural integrity. This reduction in weight contributes to improved fuel efficiency, allowing airlines to reduce operational costs while minimizing their carbon footprint.

The AGM05 incorporates a state-of-the-art fan design that enhances performance and efficiency. With a larger diameter fan and optimized blade geometry, the engine delivers higher thrust levels at lower fuel consumption rates. This design not only improves takeoff and climb performance but also ensures quieter operations, aligning with the industry's push for greener aviation solutions.

In terms of technology, the AGM05 features a sophisticated digital control system that utilizes advanced algorithms for optimal engine management. This system monitors various parameters in real time, allowing for precise adjustments to power settings, fuel flow, and environmental controls. The result is a smoother flight experience with enhanced reliability and safety.

Another notable characteristic of the AGM05 is its modular design. This aspect facilitates easier maintenance and quicker turnaround times for airlines. Engineers can access components swiftly, reducing downtime and ensuring that aircraft can return to service promptly. This is particularly important in the highly competitive commercial aviation sector, where operational efficiency translates to higher profitability.

Moreover, the AGM05 is designed with a focus on sustainability. The engine's lower emissions profile meets and often exceeds the stringent regulatory requirements set forth by aviation authorities. This commitment to eco-friendly technology positions the AGM05 as a leader in the global trend toward greener air travel.

In summary, the GE AGM05 aircraft engine showcases outstanding features such as advanced materials, superior fan design, a cutting-edge digital control system, and modularity for maintenance ease. With its emphasis on fuel efficiency and sustainability, the AGM05 not only meets the demands of modern airlines but also sets a high standard for the future of aviation technology. As the industry continues to evolve, the AGM05 is poised to play a pivotal role in shaping the next generation of air travel.