Pelco hs2500 manual Installation, Optional Heater KIT

Page 6

Installation

WARNING: When a single power source is used for both the camera and accessories, the camera power consumption must be taken into con- sideration when determining the wire gauge. Also, make certain that all electrical connections are done properly and meet electrical codes.

Before installing the HS2500 to a wall, make certain that the mounting surface is able to support four times the full weight of the enclosure, camera, and lens.

The tilt table and tilt table mounting brackets may be removed to provide adequate clearance for mounting the enclosure.

NOTE: The six fasteners required to secure the HS2500 to a wall (minimum 3/8" or 0.95 cm diameter are recommended) are not supplied.

To mount the enclosure to a wall, follow the steps outlined below.

1.Open the enclosure by unscrewing the two tamper-proof screws at the bottom and lifting the cover. A special socket tool is provided (fits 1/4" square drive).

2.Using the mounting bracket as a template, mark and drill holes in the mounting surface.

3.Attach the enclosure with the required fasteners.

4.Route the required cables through the back.

5.If you have purchased the optional heater kit, proceed to the Optional Heater Kit section.

OPTIONAL HEATER KIT

The HK8000 and HK8024 heater kits require 120 VAC or 24 VAC respectively, and both provide 80 watts of heat. The heaters are thermostatically controlled to activate ON at 40°F (4.44°C) and OFF at 60°F (15.56°C).

The following cable sizes are the minimum recommended for use with heater kits.

120 VAC Operation

24 VAC Operation

22

AWG-400 ft (121.92 m)

20 AWG-35 ft (10.67 m)

20

AWG-650 ft (198.12 m)

18 AWG-60 ft (18.29 m)

18

AWG-1,100 ft (335.28 m)

16 AWG-80 ft (24.38 m)

To install the HK8000/HK8024, perform the following steps:

1.Open the cover.

2.Attach the heater pads to each side of the tilt table bracket (refer to Figure 1).

3.Press the PC board assembly into the four holes provided in the tilt table bracket.

4.Wire according to the diagram shown in Figure 2.

6

C486M-C (9/06)

Image 6
Contents HS2500 Series High Security Camera Enclosure Page Contents List of IllustrationsImportant Safety Instructions Risk of Electric Shock Do not OpenDescription ModelsOptions Installation Optional Heater KITHK8000/HK8024 Heater Kit Installation Camera and Lens Installation Tamper Switch WiringMaintenance Specifications GeneralExploded Assembly Diagram Qty Description Part NumberProduct Warranty and Return Information ISO9001

hs2500 specifications

The Pelco HS2500 is a cutting-edge surveillance camera designed to meet the demanding needs of modern security applications. This high-performance solution is engineered for both indoor and outdoor use, making it ideal for a variety of environments ranging from retail stores to critical infrastructure sites.

One of the standout features of the Pelco HS2500 is its high-resolution imaging capabilities. With a robust sensor, the HS2500 delivers crystal-clear video output up to 1080p, ensuring that critical details are captured even in low-light conditions. This feature is enhanced by its advanced low-light technology, which allows for reliable performance during nighttime operations, providing users with around-the-clock surveillance without any degradation in video quality.

Another notable characteristic of the HS2500 is its PTZ (pan-tilt-zoom) functionality. This allows operators to remotely control the camera's position, providing flexibility in monitoring large areas. The HS2500 can smoothly pan across wide spaces, tilt to capture various angles, and zoom in on specific subjects with precision. This level of control is vital for thorough surveillance, making it easier to track activities and respond to incidents in real-time.

The HS2500 also incorporates advanced analytics for enhanced security. Features such as motion detection and object tracking enable the camera to intelligently analyze its environment, sending alerts to security personnel when suspicious movements are detected. This smart technology reduces false alarms and focuses attention where it is truly needed.

Connectivity is another strong point of the Pelco HS2500. The camera supports various network protocols, allowing for easy integration into existing security systems. With options for both wired and wireless connections, users can benefit from flexible installation, ensuring that even hard-to-reach areas can be monitored effectively.

In terms of durability, the HS2500 is built to withstand various environmental conditions. It features weather-resistant housing, which ensures reliable performance in rain, snow, and extreme temperatures. This robustness makes the camera well-suited for outdoor applications, providing peace of mind in critical surveillance scenarios.

Overall, the Pelco HS2500 represents a harmonious blend of cutting-edge technology, advanced features, and robust design, making it a top choice for organizations looking to enhance their security infrastructure. With its high-resolution imaging, PTZ capabilities, intelligent analytics, and durable construction, the HS2500 stands as a reliable guardian in today's security landscape.