SkyLink GS1 manual Introduction, Receiver Installation, Operation, Erase Transmitters

Page 1
OPEN /
CLOSE
Button
LED
Smart ButtonTM GB-318
LED
Learn
Button

Universal Garage Door

 

Remote Control

Model GS1

1. INTRODUCTION

 

 

 

Congratulations on your purchase of GS1, the package includes Skylink® garage door receiver -Smart ButtonTM GB-318, and Skylink® garage door transmitter - remote control G6T3. In this package, you will find the following:

Garage Door

Receiver

Smart ButtonTM

GB-318

 

Double Sided Tape

Crimper

Garage Door

 

 

Transmitter

 

 

G6T3

Visor Clip

Double Sided Tape

(Battery inside) Mounting

Bracket

 

Connect the receiver - Smart ButtonTM GB-318 to your current garage door opener system, you can use the transmitter - remote G6T3 to open or close the garage door.

2. RECEIVER INSTALLATION

 

Unplug the power cord of your garage door opener before installation to ensure

 

power is not connected.

 

DO NOT let children use the gargae door Transmitter without adult supervision.

WARNING

Children can injure themselves or others by the garage door.

DO NOT use remote to control the door without safety beams.

2. RECEIVER INSTALLATION (CONT)

If the Smart ButtonTM GB-318’s red LED does not flash after the Smart ButtonTM GB-318 has been connected to the wall button’s wires for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM GB-318 will still work if you plug in an adapter (purchased separately). Please

contact Skylink® to purchase the adapter.

Rating of the transformer:

12V DC, 100mA Diameter of DC plug : 3.5mm

7. Secure the SmartButtonTM GB-318 properly with the mounting accessories.

Note: Do not cut the antenna! Straighten up the antenna to improve signal reception.

Note: After installation of the “Easy Clip TM ”, if you want to re-install the Smart Button TM GB-318 to another place, please open the “Easy Clip TM ” by gently unlocking the two buckles with a screw driver, and remove it from the wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it.

3. PROGRAM TRANSMITTER G6T3 TO RECEIVER GB-318

You need to do the programming in order to add the transmitter to a receiver.

1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall

console.

2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”.

Wall Button

Ribbon Wires

NOTE:

Ensure the ribbon wires are not twisted but laid flat inside the clip.

Easy ClipTM

Smart ButtonTM GB-318 can learn up to 10 remote controls.

To add remote controls, follow the instructions below:

1.Press the learn button on the side of the Smart ButtonTM GB-318.

2.Once the learn button is pressed, the LED will flash quickly. Release the learn button.

3.Within 30 seconds, press any one of the 3 buttons on the transmitter that you want to program to the receiver.

4.Once the remote control is programmed, the LED

will flash slowly, in the same way as it flashes in standby mode.

5. You may now operate the garage door opener with this new remote control.

6. To program this transmitter to control another receiver, repeat process (1) to (4) to program another button on the remote control.

If your wall button ribbon wires are not the same kind as shown in the diagram, please refer below (4) or visit our website www.skylinkhome.com or contact us for more information.

3.Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”.

Press / lock

Ribbon Wires

4. OPERATION

If the red LED flashes slowly, the Smart ButtonTM GB-318 is in standby mode. When a valid remote control signal is received, it will open / close the garage door.

Press the programmed button on the remote control or Smart ButtonTM GB-318, it will open / close the garage door.

5. ERASE TRANSMITTERS

To erase unwanted remote control(s)from the memory of Smart ButtonTM GB-318, first erase all remote controls, then learn the one(s) you would like to keep, follow the steps below:

4.If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button.

a) Disconnect the existing wall button from the wall.

b) Connect the 2 wires from the Smart ButtonTM GB-318 to your existing wall button. Polarity does not matter, so simply pick one wire from the Smart ButtonTM GB-318 and connect it to one of the screw terminals on your wall button. Connect the 2nd wire to the other screw terminal.

c) Reconnect the wall button back.

5. If the wall button wires are hidden inside the wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door

opener.

6.Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes.

1.Press and hold the learn button for approximate 10 seconds.

2.The LED will flash rapidly after 10 seconds to indicate all the pro- grammed remote controls have been erased. You may now release the learn button.

3.You have erased all the remote controls programmed to the Smart ButtonTM GB-318.

6.TROUBLE SHOOTING

Q:What can I do if the door opener does not react after I press the button on the transmitter ?

A:- Ensure when the button on the transmitter is pressed, the red LED on the transmitter comes on. Otherwise, check if the battery is inserted properly.

-Make sure the correct button on the transmitter is pressed.

-Ensure the wires that were previously connected to the wall mounted door control are not loose.

-Ensure the transmitter has been programmed to the receiver. Refer to section 2 for how to program a transmitter to the receiver.

7. TRANSMITTER MOUNTING METHOD

This three-button remote control G6T3 can be mounted on the windshield or visor of your car with mounting accessories. First use the double sided tape to attach the mounting bracket on the windshield or use the visor clip to clip the mounting bracket on the visor, then you can put the remote control on the bracket. The remote control can also be attached to your key ring as a key fob.

Image 1
Contents Trouble Shooting Receiver InstallationIntroduction Program Transmitter G6T3 to Receiver GB-318Warranty BatteryCustomer Service

GS1 specifications

SkyLink GS1 is an advanced satellite communication system designed to meet the growing demands of modern satellite communication. Offering a robust set of features and leveraging cutting-edge technology, the GS1 is a versatile tool for various applications, including telecommunication, broadcasting, and data transmission.

One of the standout features of the SkyLink GS1 is its high-speed connectivity. It provides users with enhanced bandwidth capabilities, allowing for fast data transfer rates that are crucial for both personal and commercial uses. This system caters to a wide range of bandwidth requirements, ensuring reliable communication whether in remote locations or urban settings.

The GS1 employs advanced modulation techniques to maximize data throughput while minimizing latency. Technologies such as Adaptive Coding and Modulation (ACM) allow the satellite to adjust its transmission based on real-time conditions, ensuring optimal performance regardless of environmental challenges. This adaptability makes the GS1 an excellent choice for users who require stable connectivity in diverse situations.

In terms of hardware, the SkyLink GS1 integrates high-performance satellite antennas and transceivers. This assembly enhances signal strength and reliability, ensuring that users experience minimal interference even during adverse weather conditions. The system's design focuses on durability and longevity, providing a solution that can withstand the rigors of outdoor usage, which is particularly beneficial for industries like maritime, aviation, and disaster recovery.

Furthermore, the SkyLink GS1 supports various deployment scenarios, from portable units designed for quick setup in emergency situations to stationary systems for long-term use. The flexibility of deployment means that organizations can tailor their satellite communication solutions to meet specific needs, optimizing their operational efficiency.

Security is another critical aspect of the GS1 system. It incorporates encrypted communication protocols to protect users' data from unauthorized access. This ensures that sensitive information remains secure, which is essential for government, military, and corporate applications that require a high level of confidentiality.

Overall, the SkyLink GS1 is a state-of-the-art satellite communication solution that combines high-speed connectivity, adaptability, durability, and security. Its comprehensive features and technologies position it as a reliable choice for a wide array of communication needs in today's increasingly connected world.