SkyLink manual Model GB-318, Programming, Introduction, Installation, Operation

Smart ButtonTM
Garage Door Receiver	Model GB-318
1. INTRODUCTION

Congratulations on your purchase of the Skylink® Smart ButtonTM. The Smart ButtonTM is designed to work with Skylink® remote control G6M, G6K, G6V, G6T3 , SkylinkhomeTM system remote, and more to operate the Garage Door Opener. In this kit, you will find the following:

			Mounting Screws
			and anchors
	Smart Button		TM	Crimper
	GB-318		Double Sided Tape
		2. INSTALLATION
	Unplug the power cord of your garage door opener
WARNING	before installation to ensure power is not connected.
				Easy ClipTM

1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console.

2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”.

Wall Button

Ribbon Wires

NOTE:

Ensure the ribbon wires are not twisted but laid flat inside the clip.

Press / lock

2.INSTALLATION (CONT)

5.If the wall button wires are hidden inside the

wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door

opener.

6.Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes.

If the Smart ButtonTM GB-318’s red LED does not flash after the Smart ButtonTM GB-318 has been connected to the wall button’s wires

for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM will still work if you plug in an adapter (purchased separately). Please contact Skylink® to purchase the adapter.

Rating of the transformer:

12V DC, 100mA Diameter of DC plug : 3.5mm

7. Secure the SmartButtonTM GB-318 properly with the mounting accessories.

Note: Do not cut the antenna! Straighten up the antenna to improve signal reception.

Note:

After installation of the “Easy Clip TM ”, if you want to re-install the Smart Button TM GB-318 to another place, please open the “Easy Clip TM ” by gently unlocking the two buckles with a screw driver, and remove it from the wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it.

3. OPERATION

If the red LED flashes slowly, the Smart ButtonTM GB-318 is in standby mode. When a valid remote control signal is received, it will open / close the garage door.

	LED
Press the programmed button on the remote control
or Smart ButtonTM GB-318, it will open / close the	OPEN /

If your wall button ribbon wires

are not the same kind as shown in the diagram, please visit our

website www.skylinkhome.com or contact us for more information.

Ribbon Wires

garage door.	CLOSE
	Button

Programming

Learn additional remote controls

3.Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”.

Smart ButtonTM GB-318 can learn up to 10 remote controls. To learn additional remote controls, follow the instructions below:

1. Press the learn button on the side of the GB-318.

2. Once the learn button is pressed, the LED will

flash quickly. Release the learn button.

LED

3. Within 30 seconds, press the button on the remote control you would like to program.

4.Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode.

4.If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM to the wall button.

5. You may now operate the garage door opener with this remote control.

Erase remote controls

Learn Button

a) Dismount the existing wall button from the wall.

b) Connect the 2 wires from the Smart ButtonTM GB-318 to your existing wall button. Polarity does not matter, so simply pick one wire from the Smart ButtonTM and connect it to one of the screw terminals on your wall button. Connect the 2nd wire to the other screw terminal.

c) Mount the wall button back.

To erase unwanted remote control(s)from the memory of Smart ButtonTM GB-318, first erase all remote controls, then learn the one(s) you would like to keep.

To erase remote control(s), follow the steps below:

1.Press and hold the learn button for approximate 10 seconds.

2.The LED will flash rapidly after 10 seconds to indicate all the pro- grammed remote controls have been erased. Release the learn button.

3.You have erased all the remote controls programmed to the Smart ButtonTM GB-318.