Test Installed Faucet, Service | American Standard 3940 SERIES

4 3 1 6 8 A

	SPOUT
	O-RING	HANDLE
		HANDLE
		SCREW
		ESCUTCHEON
VALVE		RUBBER
VALVE		RING
	COUPLING	RING
	COUPLING
	NUT
		VALVE
TUBING	TEE
	TEE
COUPLING
	TUBE &
	TEE ASSEMBLY FERRULE

Prepare TUBE and TEE ASSEMBLY to fit existing VALVE location (between 6-1/2" and12"). If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE so that it will not effect the compression joint at the VALVE.

Remove COUPLING NUT and FERRULE from each VALVE and slide onto TUBING.

Push TUBING ends into VALVE side outlets. Insert VALVES into mounting holes from underside of ledge.

Press TEE onto SPOUT SHANK making certain that the O-RING is properly seated on SHANK.

Place RUBBER RING into ESCUTCHEON and screw ESCUTCHEON onto valve until snug against internal stop.

Tighten LOCKNUT to secure VALVE position. Attach COUPLING to TEE and tighten.

Slide FERRULE and COUPLING NUT to outlet of VALVE and tighten COUPLING NUT firmly.

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector.

3	HANDSHOWER INSTALLATION (Model 3901 & 3941 series only)
	IMPORTANT Check with local codes, and if required, add a vacuum breaker

kit (part no. 028708) at specified height. Refer to the instal- lation instructions supplied with the kit.

HANDSHOWER

SEAL

WASHER

HOLDER

Drop ESCUTCHEON through the fourth hole of the tub ledge (12" max from SPOUT center) with HOLDER directed towards tub center. Be sure RUBBER RING is properly seated in ESCUTCHEON. Attach RUBBER WASHER and BRASS WASHER from underside of ledge. Secure

ESCUTCHEON by tightening locknut.

Add SEAL WASHER and connect HOSE to outlet nipple on bottom of COUPLING. Tighten firmly.

Unscrew HOLDER from ESCUTCHEON. Slip SHOWER HOSE with COUPLING NUT through HOLDER and ESCUTCHEON. Install SEALS and connect both HOSES, attach HOLDER to ESCUTCHEON and connect HANDSHOWER.

NOTE When not in use, HANDSHOWER should be seated in the HOLDER.

SEAL

WASHER

HOSE

SHOWER

ESCUTCHEON

RUBBER

RING

RUBBER

WASHER

SEALLOCKNUT WASHER

SHOWER

HOSE

4	TEST INSTALLED FAUCET
		CAUTION

Turn VALVES "off" and attach handles. See separate "Instruction Sheet" for assembly of handles.

With handles in "off" position, turn on water supplies and check all connections for leaks.

Operate both handles and flush water lines thoroughly.

The flow rate of this Tub Filler exceeds 20 gallons/minute at higher water pressure. Do not fill bathtub unattended.

Lift HANDSHOWER from HOLDER, direct spray into tub, lift TRANSFER KNOB to check HANDSHOWER and HOSES for leaks.

	Check SPOUT mounting for leaks.			Turn handles "off."
5	Before the bathroom is completely finished, you may
	want to remove spout, handshower, and handles.			To remove handles, see separate "Instruction Sheet."
	KNOB	RUBBER		To remove SPOUT, proceed as follows:
	KNOB	RING		Lift TRANSFER ROD and unscrew KNOB. (Model 3901 & 3941 only).
	SET	RING
	SCREW	TRANSFER		Remove PLUG BUTTON and remove SET SCREW using hex wrench
	PLUG	ROD		supplied.
	PLUG	SHANK		Lift SPOUT off SHANK carefully and remove RUBBER RING.
	BUTTON	SHANK		Lift SPOUT off SHANK carefully and remove RUBBER RING.
		SLEEVE	SHANK	Unscrew SHANK SLEEVE and lift TRANSFFER ROD from
				SHANK (Model 3901 & 3941 only).
SPOUT				Reverse sequence to re-install SPOUT. Be sure RUBBER
				RING is properly seated in its recess at the base of the SPOUT.
				Make certain SET SCREW is properly aligned and tight so that
				SPOUT is locked in place.

6 SERVICE

To replace SHOWER HOSE, proceed as follows: Disconnect HANDSHOWER.

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position.

Remove INSERT and HANDLE SCREW.

Slip HANDLE with ADAPTER off.

Remove SPRING CLIP.

Lift STOP WASHER, turn 90° and replace.

Replace SPRING CLIP.

Replace ADAPTER, HANDLE, SCREW, and

INSERT.

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove HANDLE (see above).

Unscrew CARTRIDGE with wrench.

Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

Replace CARTRIDGE until flange is tight against valve body.

Turn valves OFF.

Replace ADAPTER, HANDLE, SCREW, and INSERT.

SPRING

CLIP

CARTRIDGE

SCREEN

STOP

WASHER

Unscrew HOLDER and pull SHOWER HOSE until hose coupling appears.

Prevent HOSE from slipping back (use clamp, tape, etc.) Disconnect SHOWER HOSE.

Remove HOLDER from old HOSE and slip over new SHOWER HOSE. Insert new SEALS and connect HOSES and HANDSHOWER.

Open valves, lift transfer knob and check for leaks.

Release HOSE, screw HOLDER back to ESCUTCHEON, and seat

HANDSHOWER.

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 223-0068

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time

IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . C A m e r i c a n S t a n d a r d I n c . 1 9 9 9

3900 SERIES, 3940 SERIES, 3901 SERIES, 3941 SERIES specifications

The American Standard 3941, 3940, 3900, and 3901 series represent a pinnacle in plumbing technology, reflecting the brand's commitment to quality and innovation. These series offer a wide array of features designed to enhance the user experience while maintaining high functionality and durability.

The 3941 series is noted for its high-efficiency performance, which is made possible through its advanced flushing technology. Utilizing a dual-flush mechanism, the 3941 allows users to choose between a full flush for solid waste and a reduced flush for liquid waste, promoting water conservation without compromising performance. The elongated bowl design enhances comfort, making this series particularly popular in residential settings.

Similarly, the 3940 series incorporates the innovative EverClean surface, which helps to inhibit the growth of stain and odor-causing bacteria, mold, and mildew. This not only keeps the toilet cleaner longer but also reduces the need for harsh chemical cleaners, making it an eco-friendly choice. The 3940 series is designed with a powerful flushing system that ensures a clean bowl with each use.

Meanwhile, the 3900 series offers a compact design that makes it an excellent option for smaller bathrooms. Despite its size, the 3900 series does not skimp on features. Equipped with a robust flushing system, it achieves maximum efficiency, making it a reliable choice for any household. The soft-close seat adds an extra layer of convenience, ensuring quiet operation and reducing wear over time.

Lastly, the 3901 series stands out with its universal height, catering to the needs of a diverse user base. This feature ensures that individuals of all ages can use the toilet with ease. The 3901 series also incorporates a water-saving design, with a flush that uses significantly less water compared to traditional models, thereby aligning with eco-conscious values.

All these series are crafted from durable materials, ensuring longevity and resistance to everyday wear and tear. Whether you choose the innovative features of the 3941 series, the cleanliness of the 3940, the compactness of the 3900, or the universal accessibility of the 3901, American Standard has designed these products to meet a variety of needs, making them a trusted choice in American homes. With an emphasis on functionality and environmental responsibility, these series exemplify American Standard's legacy of excellence in bathroom fixtures.