American Standard 2175.502 installation instructions SpeedConnect Drain

Page 5

SpeedConnect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

•Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the Drain Body Connection (2) and hand-tighten. Fig. A.

Fig. A.

1

RE-ATTACH

DISCONNECT

2

Fig. B.

Fig. C.

DOWN

CAM

 

1

 

 

CAM CAP

 

 

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig. D.

REMOVE

CAM CAP

Fig. E.

REMOVE

CAM

Fig. F.

M968881

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Install Faucet Installation InstructionsPOP-UP Drain Install Drain fromRemove Flange Below FixtureCheck Operation of POP-UP Attach Cable ConnectorMake Water Supply and Waste Connections HotcoldCheck Drain Connections Test Installed FittingService SpeedConnect Drain Fig. G

2175.502 specifications

The American Standard 2175.502 is a highly regarded bathroom fixture, specifically known for its innovative design and exceptional performance. As part of the esteemed American Standard brand, which has a long-standing reputation for quality and craftsmanship, the 2175.502 model combines form and function in a seamless manner.

One of the key features of the American Standard 2175.502 is its sleek and modern aesthetic. It is designed to complement a variety of bathroom styles, ranging from minimalist to contemporary. The clean lines and elegant curves not only enhance its visual appeal but also make it easy to integrate into various decors.

This model boasts a single-handle design that provides effortless control over both water flow and temperature. The ergonomic handle helps ensure a smooth and intuitive user experience, making it ideal for families and individuals alike. The faucet is equipped with a ceramic disc valve, which is renowned for its durability and ability to prevent leaks, ensuring that you can enjoy years of worry-free operation.

In terms of technology, the American Standard 2175.502 features a WaterSense certification, which signifies that it meets strict water efficiency guidelines set by the Environmental Protection Agency. This means the faucet uses significantly less water without sacrificing performance, making it an environmentally friendly choice. The low-flow aerator helps to optimize water usage while maintaining a steady and comfortable stream.

Another standout characteristic of the 2175.502 is its easy installation process. The product comes with all necessary mounting hardware, and the straightforward design allows for a quicker setup, saving both time and effort. Additionally, the durable finish resists tarnishing and corrosion, ensuring that the faucet maintains its luster for years to come.

The American Standard 2175.502 also incorporates features that enhance user safety. The temperature limiter allows users to set a maximum hot water temperature, reducing the risk of scalding, which is particularly beneficial in households with young children or elderly members.

Overall, the American Standard 2175.502 blends style, functionality, and advanced technology, providing an efficient and reliable option for modern bathrooms. Its thoughtful design, combined with features geared toward water conservation and user safety, makes it a top choice for homeowners seeking quality and sustainability in their bathroom fixtures.
Top Page Image Contents