Install WAX Seal

INSTALLATION INSTRUCTIONS

Champion®4

Model 2004 Normal Height Elongated One Piece Toilet

Model 2034 Right Height™ Elongated One Piece Toilet

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

NOTE: BACK-TO-BACK INSTALLATION

Depending upon your plumbing and venting conditions, the flow from the Champion in a back-to-back installation may create a vacuum on the system and draw water from the opposing bowl. The National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over is possible. The code does approve a directional "Y" style fitting with proper venting to direct the water

downward and away from the other toilet.		Recommended fitting type for back-to-back installations.
RECOMMENDED TOOLS AND MATERIALS
Regular Screwdriver	Adjustable Wrench	Putty Knife	Sealant	Carpenters Level
Wax Ring/Gasket	Flexible Supply Tube	Closet Bolts	Hacksaw	Tape Measure

1REMOVE OLD TOILET

a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

2ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

T U R E U S E

FINISHED WALL

29-3/4Model 2004

(756mm)

1-3/4 (44mm)
8	C/L OF SEAT		16-3/4
	POST HOLES		16-3/4
			(425mm)
(203mm)
	5-1/2 (140mm)


	CENTERS
	18-1/2
	(470mm)
1
(25mm)
		SUPPLY	17-3/4
		SUPPLY	(451mm)
		AS	28-1/8
		REQ'D	(714mm)
		15
4		(381mm)	7
4
(102mm)
(102mm)			(178mm)
			(178mm)
1-1/4	1/2	*4-1/2	FINISHED
(32mm)	(13mm)	*4-1/2	FINISHED
10-3/4	13-1/2	(114mm)	FLOOR
(273mm)	(343mm)		10-3/4
12	C/L OF OUTLET		(273mm)
(305mm)	C/L OF OUTLET

FINISHED WALL
	29-3/4		Model 2034
	(756mm)		Model 2034
1-3/4 (44mm)
8	C/L OF SEAT		16-3/4
8	POST HOLES		(425mm)
(203mm)	POST HOLES
	5-1/2 (140mm)


	CENTERS
	18-1/2
	(470mm)
1
(25mm)
		SUPPLY	17-3/4
		SUPPLY	(451mm)	29-1/2
		AS		29-1/2
		REQ'D		(749mm)
		16-1/2
3-3/4		(419mm)	7
3-3/4
(95mm)
(95mm)			(178mm)
			(178mm)
1-1/4	1/2	*4-1/2		FINISHED
(32mm)	(13mm)	*4-1/2		FINISHED
10-3/4	13-1/2	(114mm)		FLOOR
(273mm)	(343mm)		10-3/4
12	C/L OF OUTLET		(273mm)
(305mm)	C/L OF OUTLET
(305mm)

S A V E F O R F U

CLOSET

FLANGE

CLOSET

BOLTS

INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152mm) apart and parallel to wall.

SEALANT	WAX RING

Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

NUT

TAPERED

WASHER

	CLOSET	FLANGE
	BOLT	FLANGE
	BOLT

POSITION TOILET ON FLANGE

a.Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.

b.Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up!

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .	730865-100 Rev. H
© A m e r i c a n S t a n d a r d I n c . 2 0 0 7