American Standard 0790.400 dimensions Town Square Pedestal Sink, Town Square 24 Pedestal Sink

TOWN SQUARE® 24"

PEDESTAL SINK

FIRECLAY

TOWN SQUARE® 24" PEDESTAL SINK

•American classic design

•Clean straight lines with classic ogee curves

•Rear overflow

•Supplied with mounting kit

•Design-matched to Town Square fixture and faucets

•Right Height™ for greater comfort during use

•Made from fireclay

❏0790.400 Faucet holes on 4" (102mm) centers

❏0790.800 Faucet holes on 8" (203mm) centers

❏0790.100 Center hole only

Nominal Dimensions: 24" x 20-1/4" x 35-1/2" (610 x 514 x 902mm)

Separate Components:

❏0790.004 Pedestal top 4" (102mm) centers

❏0790.008 Pedestal top 8" (203mm) centers

❏0790.001 Center hole only

❏0031.000 Pedestal only

Bowl sizes:

14" (356mm) wide

11-3/4" (298mm) front to back

6-1/2" (165mm) deep

Compliance Certifications -

Meets or Exceeds the Following Specifications:

•ASME A112.19.9M for Non-Vitreous Ceramic Fixtures

•CAN/CSA B45 Series

To Be Specified:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black

❏Town Square Faucet:

❏Centerset Lavatory Faucet: 2555.201 (shown)

❏Widespread Lavatory Faucet: 2555.801

❏Other Lavatory Faucet*:

❏Faucet Finish:

❏Supplies:

❏1-1/4" Trap:

* See faucet section for additional models available

© 2008 AS America Inc.

FINISHED WALL	4"	18-3/4" (476mm)	2-5/8"	4"
	(102mm)		(67mm)	(102mm)
9-1/2"
(241mm)				5/8"
			(16mm)
				20-1/4"
				(514mm)
1-3/4" DIA.
STD. DRAIN
OUTLET
	PED BASE		PED TOP
	OUTLINE		OUTLINE
		24"
		(610mm)		3-3/4" (95mm)	DRAIN
					CHASE
3/8" (10mm) DIA.				7-1/2"
				(191mm)
SLAB ANCHOR
SCREW HOLES
ON 18-3/4" (476mm)			6"
CTRS
			(152mm)
			SUPPLIES AS
			REQUIRED	35-1/2"
			1-1/4" O.D.
*24"				(902mm)
			WASTE	28"
(610mm)					OPEN
	*22"		(711mm)
					TO
	(559mm)
			3/8" (10mm) DIA.		FLOOR
			BASE ANCHOR
			SCREW HOLES
			ON 6" (152mm)
			CTRS
			10"
FINISHED			(254mm)
FLOOR
		6"
		(152mm)

NOTES:

*DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.

▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.

■ FOR REINFORCEMENT ONLY. TAKE ACTUAL DIMENSIONS FROM FIXTURE.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.9M.

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

J4

Revised 2/08