PYLE Audio PT-4001X, PT-1201X Stereo or Mono Inputs, Speaker connections, Bridged Mode Operation

EQ OR MIXER	use XLR/6.35 mm
	combo jacks

EQ OR MIXER use RCA jacks

Stereo or Mono Inputs

Your Pyle Pro amplifier can be operated in Stereo, Mono or Bridged mode, depending on the input source. If the input signal is mono, slide the Stereo/Mono/Bridged selector switch to MONO and the signal will be routed through both channels. If you wish to run the amplifier in bridged output mode, slide the switch to Bridged.

Speaker connections

You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to Channel 1 and/or Channel 2 of the amplifier. If you connect two pairs of speakers, be sure to follow these guidelines:

STEREO OPERATION

SWITCH IN “STEREO” POSITION

CH 2 CH 1

STEREO SIGNAL SOURCE

MONO OPERATION

SWITCH IN “MONO” POSITION

CH 2 CH 1

MONO SIGNAL SOURCE	USE
	CHANNEL 1
	INPUT ONLY

CH 2 CH 1

Bridged Mode Operation

This amplifier can operate in a mono bridged output mode, if your speakers can handle the following power output levels:

As shown in the diagram below, connect the speaker's positive

(+)to the amplifier's red speakers left (1/2) terminals and negative (-) to red speakers right (1/2) terminals.

The speaker right (+) on the amplifier is used as a negative (-) terminal for a bridged connection.

NOTE: The extra amplifier output of 6.35mm phone jacks can not be used for the bridged connection. It can only be used in normal (non-bridged) operation as a stereo speaker output.

MONO BRIDGED OPERATION

SWITCH IN “BRIDGED” POSITION

DO NOT USE

BLACK TERMINALS

MONO SIGNAL SOURCE	USE
	CHANNEL 1
	INPUT ONLY

•Speakers which are connected to the same channel are part of a pair, and must be of the same impedance.

•Speakers connected to different channels are NOT part of a pair, and can be of different impedances.

1.Prepare the speaker wire by removing about 1 inch of insulation from the end of the speaker wire you intend to connect to the amplifier. Then twist the exposed wire to secure all the wire strands.

NOTE: Use 16-gauge speaker wire for lengths up to25 feet; 14-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible.

2.Connect the speaker wires to the speaker's positive and negative terminals.

NOTE: Most speaker terminals are either color-coded or have a mark that indicates the terminal's polarity. Usually positive terminals are red or have a plus symbol (+), and negative terminals are black or have a minus

STEREO SIGNAL SOURCE

CH 2	CH 1
BALANCED-)	INPUTS
OUTPUTS	CAUTION: DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.

USE CHANNEL 1 INPUT ONLY

CH 2

MONO SIGNAL SOURCE

CH 1

DO NOT USE

BLACK TERMINALS

USE	MONO SIGNAL SOURCE
CHANNEL 1
INPUT ONLY

DO NOT USE

BLACK TERMINALS

symbol (-).

3.Connect the speaker wires to the amplifier's left and right speaker terminals according to the terminal color polarity.

CH-2	CH-1	HOT(+) COLD(	GND(+)	FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
				CAUTION: REPLACE ONLY WITH SAME TYPE FUSE.
				TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
		2	1	CAUTION: PLUG WITH AN EXTENSION CORD RECEPTACLE
		3		OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
				INSERTED TO PREVENT BLADE EXPOSURE
~ AC 120V 60HZ	BRIDGE			INPUTS	CAUTION
			CH-2	CH-1
					RISK OF ELECTRIC SHOCK
					DO NOT OPEN
GND				CH-2	CH-1	MONO
	GROUND LIFT					STEREO BRIDGE

GROUND LIFT

STEREO SIGNAL SOURCE

CAUTION! Do not use balanced and unbalanced inputs simultaneously!!

OUTPUTS		BALANCED)		INPUTS
		HOT(+) COLD(-	GND(+)		CAUTION: DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
CH-2	CH-1				FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
					CAUTION: REPLACE ONLY WITH SAME TYPE FUSE.
		2	1		CAUTION: PLUG WITH AN EXTENSION CORD RECEPTACLE
					TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
		3			OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
					INSERTED TO PREVENT BLADE EXPOSURE
~ AC 120V 60HZ	BRIDGE				INPUTS	CAUTION
			CH-2		CH-1	RISK OFDO NOT OPEN
GND					CH-2	CH-1	MONO
	GROUND LIFT						STEREO BRIDGE
GROUND	LIFT

MONO SIGNAL SOURCE	USE
	CHANNEL 1
	INPUT ONLY

CAUTION! Do not use balanced and unbalanced inputs simultaneously!!

OUTPUTS		BALANCED)		INPUTS
		HOT(+) COLD(-	GND(+)		CAUTION: DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
CH-2	CH-1				FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
					CAUTION: REPLACE ONLY WITH SAME TYPE FUSE.
		2	1		CAUTION: PLUG WITH AN EXTENSION CORD RECEPTACLE
					TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
		3			OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
					INSERTED TO PREVENT BLADE EXPOSURE
	BRIDGE				INPUTS	CAUTION
~ AC 120V 60HZ			CH-2		CH-1
							ELECTRIC SHOCK
						RISK OFDO NOT OPEN
GND					CH-2	CH-1	MONO
	GROUND LIFT						STEREO BRIDGE
GROUND	LIFT

MONO SIGNAL SOURCE	USE
	CHANNEL 1
	INPUT ONLY

CAUTION! Do not use balanced and unbalanced inputs simultaneously!!

PYLE PRO PT-1201X/1601X/2001X/4001X Amplifier Owner’s Manual - 4 5 - PYLE PRO PT-1201X/1601X/2001X/4001X Amplifier Owner’s Manual