Over-Firing, Seasonal use, ASH Removal

OPERATING INSTRUCTIONS

3.12We would recommend that the stove be burnt at high output for at least 30 minutes each day when it is in use. This will help reduce the build-up of tars and creosotes within the stove and flue system.

4.BURNING SOLID FUEL (with multifuel kit fitted)

Do not burn painted, impregnated wood or manufactured board products.

4.1Open the Airwash control to approximately 50% and Primary air control fully.

4.2Place some pieces of firelighter or dry crumpled paper on the grate and cover with some small pieces of dry kindling wood. Light the paper or firelighters.

4.3To avoid the build-up of condensation on the door glass it is advisable to leave the door slightly open as the fire establishes, and the glass warms.

4.4As the fire becomes established add pieces of solid fuel and fully close the door. Do not leave the stove with the door open as this could over-fire the stove and cause permanent damage.

4.5As the fire becomes established reduce the Airwash control to approximately 25% and control the burn rate using the Primary air control only.

4.6To burn solid fuel efficiently it is best to control the combustion using the Primary air control only.

4.7Before re-fuelling the stove it is advisable to first de-ash the firebed, using the riddling grate system. To do this open the stove door, then using the ashpan tool move the grate vigorously left to right. This causes the ash to fall down into the ashpan. Do not use bare hands to operate the riddling system.

4.8Then open the Primary air control fully for a few minutes, to establish a glowing bed before adding new fuel. Allow the new fuel to burn at high output for a few minutes before adjusting the burn rate with the Primary air control to the desired setting. It is best to refuel little and often to maintain clean and efficient burning.

4.9The ideal control settings to suit the particular installation and personal preferences will be established by experience in using the stove.

4.10Do not load fuel higher than the log guard at the front of the stove and the secondary combustion air inlet holes at the back of the fire box.

4.11We would recommend that the stove be burnt at high output for at least 30 minutes each day when it is in use. This will help reduce the build-up of tars and creosotes within the stove and flue system.

Do not burn bituminous coal, ‘petro-coke’ or other petroleum based fuels, as this will invalidate any product guarantee.

5.OVER-FIRING

5.1Do not use the appliance at maximum output for prolonged periods of time, or over fill the firebox with fuel, as this could result in over-firing. If the connecting fluepipe, appliance flue collar or top plate glow red with heat the appliance is being over fired and the air controls should be closed to reduce the output.

5.2If a chimney fire occurs shut all air controls immediately to close the appliance down, and evacuate all persons from the building before calling the fire brigade. Do not re-enter the building until it is confirmed safe to do so.

5.3Following a chimney fire do not use the appliance until it is inspected by a HETAS (GB only)/ INFO (Eire) registered installer, to confirm that the appliance is safe to use, or make any repairs required before re-use. Only genuine Stovax replacement parts are to be used to keep your appliance in safe and efficient working order.

5.4After any chimney fire it is recommended that the chimney system be inspected and swept by a NACS registered (UK only) chimney sweep, to confirm that the system is structurally sound and free from any obstructions before re-use.

6.seasonal use

6.1If the stove is not to be used during the warmer periods of the year it is recommended to clean and service the stove, as detailed in the Maintenance and Servicing section.

6.2The air controls should be set in the 50% open position to keep the appliance ventilated, and stop the build-up of any moisture inside.

6.3Before re-lighting the stove remove the baffles, clear any debris that may have accumulated, and check the flue is clear of any blockages.

7.ASH REMOVAL

7.1The burning of any fuel will produce ash, which will have to be removed after a period of use. This time will depend on the fuel used. Before removing the ash from the stove it is advisable to let the fire burn down to a low level, or even go out completely. If a multifuel kit is fitted the ashpan can be removed from the stove using the tool provided, after opening the door.

7.2As heat can remain in the ash for a long period after use, care must be taken when removing and carrying the full ashpan. We suggest that the ashpan be carried using gloved hands, or the ash is placed directly into a Stovax Ash Caddy. (Stovax Part No. 4227).

7.3When burning wood the amount of ash will be smaller and may only need removal once every week. To do this, allow the fire to burn out and cool. Then after removing the log

7118 specifications

The Stovax 7118 is a distinguished model in the realm of wood-burning stoves, designed to deliver both functionality and aesthetic appeal for modern homes. Its elegant appearance and robust construction make it a favored choice among consumers seeking efficient heating solutions.

One of the standout features of the Stovax 7118 is its impressive heating capacity, making it suitable for medium to large spaces. With a nominal output of approximately 5-8 kW, this stove can effectively warm up to 150 square meters, ensuring that your living area remains cozy even during the coldest months.

The design of the Stovax 7118 underscores its contemporary style while incorporating traditional elements. Its clean lines and minimalist finish allow it to blend seamlessly into various interior settings. Available in multiple finishes, including classic black and sleek metallic options, homeowners can customize the stove to match their décor preferences.

An essential technology integral to the Stovax 7118 is its efficient combustion system. This model employs a secondary air supply that helps to enhance the burn rate of the wood, allowing for more complete combustion. This not only improves efficiency but also reduces emissions, making the stove an environmentally-friendly option. The inclusion of a riddling grate allows for easy ash management, complementing the overall user-friendly design.

Another significant characteristic of the Stovax 7118 is its large panoramic glass door, which offers an unobstructed view of the fire. This feature is particularly appealing, creating a warm inviting atmosphere while allowing users to enjoy the flickering flames. The airwash system incorporated in the design also keeps the glass clean, providing an uninterrupted view of the fire and minimizing maintenance.

Safety is a paramount consideration in the design of the Stovax 7118. It features a robust construction with heat-resistant materials, ensuring user safety during operation. Additionally, the stove is designed for easy installation with flexibility in flue options, accommodating an array of home configurations.

In conclusion, the Stovax 7118 exemplifies the perfect blend of efficiency, style, and practicality. With its advanced heating technology, striking design, and user-friendly features, it stands out as an excellent choice for anyone looking to elevate their home heating experience. Whether you are heating a cozy cabin or a modern home, the Stovax 7118 is a stove that promises warmth, beauty, and reliability.