Stovax Logic Hotbox & Convector Fire manual User Instructions

Page 4

USER INSTRUCTIONS

1.GENERAL

1.1Installation and servicing must only be carried out by a competent person.

1.2In all correspondence, please quote the appliance type and serial number, which can be found on the databadge adjacent to the control knob.

1.3Ensure that curtains are not positioned above the fire, and that there is a 300mm minimum clearance between the sides of the fire and any curtains.

1.4This product is guaranteed for 12 months from the date of installation, as set out in the terms and conditions of sale between Gazco and your local Gazco dealer. Please consult with your local Gazco dealer if you have any questions. In all correspondence always quote the Model Number and Serial Number.

1.5Parts of this appliance become hot during normal use. It is therefore recommended that a suitable fire guard be used for protection of young children and the infirm.

2.LIGHTING THE FIRE

2.1Locate the control valve on the appliance. There are two control knobs on the valve, the right hand knob controls the pilot ignition and the left hand knob controls the main burner.

2.2If your appliance has already been upgraded to battery remote control, please refer to the instructions provided with the upgrade to operate the remote control. The following instructions will work for either situation.

1

2.3Ensure that the left-hand control knob is pointing to off ( ).

2.4Ensure that the right hand control knob is pointing to off ( ).

2.5Press in the right hand control knob and rotate it anti-clockwise until a click is heard (keep pressing in) and the knob is pointing to pilot ( ). The pilot should now light. If the pilot has not lit, repeat the procedure until it does.

2.6Keep the control knob pressed for 10 seconds and then release it, the pilot should stay alight. If the pilot goes out, repeat the procedures until it does.

2.7If the pilot will not light after repeated attempts, contact the retailer or installer from whom the appliance was purchased.

2.8Turn the right hand control to point to main burner ( ). The appliance can now be controlled using the left hand control knob.

2.9Turn the left hand control knob to point to low fire ( ), the main burner will light on low. The burner can now be controlled between low and high settings. Turn the control

knob anticlockwise increase the flame height and clockwise to decrease the flame height.

THE YELLOW FLAMES WILL APPEAR WHEN THE FIRE HAS GAINED SUFFICIENT HEAT - TYPICALLY 10 TO 20 MINUTES.

3.TURNING THE FIRE OFF

3.1To turn the fire off, locate the control valve, turn the left-hand control knob until it points to off ( ). The main burner will go out leaving the pilot burning.

3.2To turn the pilot off, locate the control valve, turn the right hand control knob until it points to off ( ), the pilot will go out.

4.LIGHTING THE FIRE WITH A MATCH

If the pilot does not ignite as described in Section 2, please consult your GAZCO dealer to rectify the problem. However, the appliance may be lit as a temporary measure using the following procedure:

4.1Press in the right hand control knob and rotate it anti- clockwise until a click is heard (keep pressing in) and the knob is pointing to pilot ( ), apply a lighted match to the pilot hood, see diagram 2.

2

4.2When the pilot is alight, extinguish the match and continue to depress for 5 to 10 seconds.

4.3The fire may now be controlled as previously described.

5.UPGRADING YOUR FIRE

5.1Your fire is fitted with a control valve that can easily be upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local Gazco stockist.

5.2STANDARD REMOTE CONTROL This remote control can control the fire after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning GAZCO PART NUMBER 8455.

5.3IMPORTANT - there is a thermostatic version of the upgrade but this is NOT SUITABLE for open flame fires like the Logic.

4

Image 4
Contents Logic Hotbox & Convector Fire Contents Flue Check Pass Fail Appliance Commissioning ChecklistGAS Check User Instructions Cleaning the Fire Arrangement of Fuel BED ComponentsFront ROW Coal Layout Using Flat Fire Fronts Front ROW Coal Layout Using Curved Fire FrontsCoal Layout Coal Layout from Front ROWInstallation Details Oxygen Depletion SensorFlame Failure Device 10. ‘RUNNING IN’Installation Instructions Technical SpecificationP8308MCUC GAS Category ConvectorInstallation Instructions Flue and Chimney Requirements Site RequirementsAppliance Location GAS Supply AIR Vents Must not be RestrictedInstallation Installation of the Appliance Cable Retention MethodScrew Fixing Method Front ROW Coal Layout Using Curved Fire Fronts Coal Layout Front ROW Coal Layout Using Flat Fire FrontsCoal Layout from Front ROW AR1173 Installation / Commissioning CommissioningServicing Servicing InstructionsServicing Requirements Ignition Functional Check Pilot will not Light Ignition Functional Check No SparkFault Finding Charts Replacing Parts Ignition LeadPiezo ODS Pilot UnitGAS Valve MAG Unit Main InjectorChanging Between GAS Types Spares Part Lists

Logic Hotbox & Convector Fire specifications

The Stovax Logic Hotbox and Convector Fire represents a significant advancement in home heating solutions, combining sleek design with efficient performance. This innovative fireplace system offers a modern twist on traditional heating methods, making it a popular choice for homeowners seeking both aesthetics and functionality.

One of the main features of the Stovax Logic Hotbox is its high efficiency rating. Designed to provide a clean and powerful heat output, this fire utilizes advanced combustion technology to ensure that a greater percentage of the fuel is converted into heat. This not only maximizes warm air flow within the home but also minimizes emissions, making it an environmentally responsible choice.

The Hotbox model is equipped with a large glass window that provides an expansive view of the flames, creating a warm and inviting atmosphere. This feature not only enhances the visual appeal of the fire but also enables homeowners to enjoy the relaxing ambiance that a real flame provides. The front-loading design of the fire makes it easy to load fuel, ensuring prolonged burning cycles and reduced maintenance.

The Stovax Logic Convector Fire variant further enhances the heating efficiency through its unique convection technology. This system draws in cool air from the room, circulates it around the fire chamber, and then gently releases the warmed air back into the room. This process ensures that heat is distributed evenly throughout the space, maximizing comfort while reducing energy consumption.

In terms of customization, the Stovax Logic range offers various design options, allowing users to select from different sizes and finishes to match their home décor. With stylish choices ranging from contemporary to more traditional styles, homeowners can integrate the fire seamlessly into their living spaces.

Safety is also a top priority for the Stovax Logic Hotbox and Convector Fire. Equipped with features such as a heat-resistant glass and a secure casing, these fires are designed to perform safely in any home environment.

Overall, the Stovax Logic Hotbox and Convector Fire stand out as an ideal choice for those seeking a combination of elegant design, advanced technology, and efficient heating. Whether you are updating your existing fireplace or considering installing a new one, this innovative solution promises to deliver both comfort and style, making it an intelligent addition to any home.