Stovax P8050 manual Safety precautions, Installation of the stove

Page 10

INSTALLATION INSTRUCTIONS

INSTALLATION

IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS AT THE FRONT OF THE BOOKLET.

LPG MODELS: THE APPLIANCE IS FACTORY SET TO RUN ON BUTANE G30. IF IT IS INTENDED TO BE USED ON PROPANE G31 THE AERATION PLATE SUPPLIED MUST BE FITTED.

FOR DETAILS OF CHANGING AERATION PLATES REFER TO SECTION 29.

FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SECTION 30.

1.safety precautions

1.1This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space. Place read these instructions before installation and use of this appliance.

1.2All the instructions must be left intact with the user.

1.3In your own interest, and those of safety, this appliance must be installed by a competent person in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution.

1.4This appliance is intended for use on a governed gas installation and set to the required pressure.

1.5Keep all plastic bags away from young children.

1.6Do not place any object on or near to the stove. Allow adequate clearance above the stove, see Technical Specification.

1.7The stove is fitted with the Gazco Flue Sure System, which will act to cut off the gas supply to the appliance in the event of incorrect operation of the flue. If the system acts to shut off the gas supply, this indicates that there is insufficient flue pull. If this occurs a minimum of 10 minutes should be allowed before trying to relight. Continued operation of this safety device means that there may be a serious problem with the flue system; a qualified gas engineer should inspect this. DO NOT USE THE STOVE UNTIL AN ENGINEER

SAYS IT IS SAFE TO DO SO.

1.8The Flue Sure System must not be tampered with. Use only genuine Gazco replacement parts when servicing the system

-refer to servicing section on page 15.

2.installation of the stove

2.1• Remove the outer carton

• Take the stove off the pallet and remove the accessory carton.

2.2• Position the stove ensuring all appropriate clearances are observed.

2.3Having run the gas supply to the stove, PURGE THE SUPPLY PIPE, this is essential to expel any debris that may block the gas controls.

• Connect the gas supply to the 8mm-compression elbow at the RH rear corner of the stove, Diagram 3.

3

AR0396

2.4• Check the pull of the flue system by applying a lighted smoke pellet to the flue system opening.

If there is a definite flow into the chimney, proceed with the installation, if not warm the chimney for a few minutes.

IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY REQUIRE ATTENTION - SEEK EXPERT ADVICE

2.5The flue system may now be connected to the stove:

•Ensure that all joints are sealed with a suitable fire resistant sealant.

It is also recommended that a physical retention method be used at the flue spigot joint, self-tapping screws being favoured.

2.6• Connect a suitable pressure gauge to the test point located on the inlet fitting,

•Turn the gas supply on

•Light the appliance and check all gas joints for possible leaks

•Turn the appliance to a maximum and check that the supply pressure is as stated on the databadge.

•Turn the gas off and replace the test point screw

•Turn the gas on and check the test point for leaks.

NOTE: The stove is also suitable for installation onto a fireplace opening. The following method illustrates how this can be achieved with the aid of the optional closure plate and spigot extension:

•Ensure that the fireplace dimensions are shown in

Diagram 4.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Brunel Mk Contents Pass Fail APPLIANCE COMMISSIONING CHECKLISTFLUE CHECK GAS CHECKLighting the appliance User InstructionsGeneral Turning the stove offCleaning the Stove Fuel bed arrangementGazco flue sure system Flame failure deviceServicing Installation detailsRunning VentilationInstallation Instructions Technical SpecificationFlue and Chimney Requirements Installation of the gas supplySITE REQUIREMENTS Appliance locationSafety precautions InstallationInstallation of the stove Fuelbed Arrangement Lighting Commissioning CommissioningServicing Instructions Servicing / Fault Finding ChartsServicing Requirements Ignition Functional Check Flame Failure Functional CheckPILOT UNIT Replacing PartsGeneral Ignition Lead and PiezoMain Injector Magnetic Safety ValveGazco Flue Sure System Changing Between GAS Types Primary Aeration PlateShort Spaes List SERVICE RECORDS Member of the Stovax Group

8050, P8050 specifications

The Stovax P8050 and P8050 are elegant and efficient wood-burning stoves designed to combine modern aesthetics with advanced heating technology. These stoves are crafted for homeowners looking to create a cozy atmosphere while maximizing energy efficiency.

One of the standout features of the Stovax P8050 series is its cleanburn technology. This innovative combustion system enhances burning efficiency by promoting a more complete combustion process. As a result, users benefit from increased heat output with lower wood consumption, making it an eco-friendly choice. The intelligent design also minimizes emissions, contributing to cleaner air quality.

The P8050’s large glass window is another noteworthy characteristic, providing a stunning view of the flames. This not only enhances the visual appeal of the stove but also allows users to enjoy the ambiance of a traditional wood fire from various angles. The design includes integrated airwash technology, which keeps the glass clear by directing a flow of air across the surface. This feature ensures a consistently unobstructed view of the fire while also reducing maintenance needs.

In terms of versatility, the Stovax P8050 is available in different configurations to meet diverse installation needs. It can be installed as a freestanding unit or inset into a fireplace, allowing flexibility in design and placement. The stove is also compatible with a range of flue systems, making it suitable for various homes and settings.

Another significant feature is the stove's efficient heat output, which can effectively warm large living spaces. The adjustable heating controls allow users to fine-tune the temperature, ensuring optimal comfort regardless of external weather conditions.

Furthermore, the P8050 is constructed from high-quality materials, ensuring durability and longevity. Its contemporary design is complemented by a range of finishes, allowing it to seamlessly blend into various interior styles while providing functional elegance.

Overall, the Stovax P8050 and P8050 are ideal options for anyone seeking an efficient, stylish, and environmentally responsible wood-burning stove. With their innovative technologies, aesthetic appeal, and robust performance, these stoves truly stand out in the modern heating market.
Top Page Image Contents