Stovax 8543-P8543 Control Upgrade, Safety Precautions, Installation of the Stove, GAS Supply

Page 12

INSTALLATION INSTRUCTIONS

INSTALLATION

IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS OF THIS BOOKLET.

FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SERVICING INSTRUCTIONS, REPLACING PARTS.

1.CONTROL UPGRADE

1.1This stove is fitted with a control valve that can be easily upgraded to battery powered remote control. There are two versions of this control which can be obtained through your local Gazco stockist.

1.2This upgrade can be fitted before or after installation but if side clearances are limited then it will be easier to upgrade the stove before installation. Full instructions are included with the kit.

1.3STANDARD REMOTE CONTROL. This remote controls the gas appliance after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning GAZCO PART NUMBER 8455.

1.4THERMOSTATIC AND TIMER REMOTE CONTROL. This remote controls the gas appliance after the pilot has been lit. In ‘MANUAL MODE’ it can be used to turn the main burner on and manually regulate it from low through to high and back again. It can also be used to turn the main burner leaving the pilot burning. In ‘AUTO MODE’ it will automatically regulate the room temperature to a pre-set temperature. In ‘TIMER MODE’ it will turn the fire on and off according to a pre-set programme and automatically regulate the room temperature during the two ON periods. GAZCO PART NUMBER 8456.

2.SAFETY PRECAUTIONS

2.1This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space. Place read these instructions before installation and use of this appliance.

2.2All the instructions must be left intact with the user.

2.3In your own interest, and those of safety, this appliance must be installed by a competent person in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution.

2.4This appliance is intended for use on a governed gas installation and set to the required pressure.

2.5Keep all plastic bags away from young children.

2.6Do not place any object on or near to the stove. Allow adequate clearance above the stove. See diagram 2 above, Appliance Location.

2.7The stove is fitted with the Gazco Flue Sure System, which acts to cut off the gas supply to the appliance in the event of incorrect operation of the flue. If the system acts to shut

off the gas supply, this indicates there is insufficient flue pull. If this occurs a minimum of 10 minutes should be allowed before trying to relight. Continued operation of this safety device means there may be a serious problem with the flue system and a qualified gas engineer must inspect.

DO NOT USE THE STOVE UNTIL AN ENGINEER SAYS IT IS SAFE TO DO SO.

2.8Do not tamper with the Flue Sure System Use only genuine Gazco replacement parts when servicing the system - refer to Servicing Instructions, Replacing Parts.

3. INSTALLATION OF THE STOVE

Flue Pipe Installation

3.1Open the carton and remove the accessory carton and stove unit. Decide upon top or rear flue exit. The stove is factory built for rear flue exit, but it may be changed to top exit by using the following method:

3.1.1Remove the flue spigot from the rear of the stove and replace with the blanking plate from the top of the stove.

3.2Position the stove ensuring all appropriate clearances are observed. Using a pencil, mark the position of the holes in the fixing brackets attached to the inside of the rear legs.

3.3Remove the stove and drill the holes using a number 12 masonry drill. Push rawlplugs into the holes and insert the woodscrews until the head is approximately 3mm proud of the hearth. Place the stove in position so that the screw head is located in the large part of the slot in the bracket. Push the stove back so that the screw heads engage fully into the narrow part of the slot. Tighten the screws if desired.

4.GAS SUPPLY

4.1Having run the gas supply to the stove, PURGE THE SUPPLY PIPE. This is essential to expel any debris that may block the gas controls. Connect the gas supply to the 8mm- compression elbow at the RH rear corner of the stove.

3

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Clarendon and Ashdon Coal Effect Stove Range Contents Appliance Commissioning Checklist Flue Check Pass FailGAS Check User Instructions GeneralLighting the Appliance Cleaning the Fire Advice on Handling and disposal of fire ceramicsTurning the Stove OFF Upgrading Your StoveSmall Clarendon Medium Claendon and Ashdon Large Clarendon Installation Details Gazco Flue Sure SystemFlame Failure Device RunningInstallation Instructions Technical SpecificationInstallation of the GAS Supply Site RequirementsFlue and Chimney Requirements Appliance LocationInstallation Control UpgradeSafety Precautions Installation of the StoveFuel BED Arrangement Medium Clarendon and Ashdon Large Claendon Installation Instructions Commissioning CommissioningServicing / Fault Finding Charts Servicing InstructionsFault Finding Charts Ignition Functional CheckFlame Failure Functional Check Replacing Parts Burner Unit RemovalPilot Unit Ignition Lead and PiezoPiezo Magnetic Safety Valve GAS ValveMain Injector Primary Aeration PlateChanging Between GAS Types Short Spares List LPGService Records Page Page Member of the Stovax Group

8542-P8542, 8518-P8518, 8519-P8519, 8543-P8543, 8517-P8517 specifications

Stovax is renowned for its commitment to combining traditional craftsmanship with modern technology in the realm of wood-burning stoves, and the models 8519-P8519, 8542-P8542, 8517-P8517, Clarendon 8541-P8541, and 8543-P8543 exemplify this ethos. Each of these stoves is designed to produce a timeless aesthetic while incorporating cutting-edge features that enhance efficiency and performance.

The Stovax 8519-P8519 and 8517-P8517 models showcase a classic design with a cast-iron body that provides excellent heat retention. These stoves feature a large glass viewing window that allows for a delightful view of the flames, enhancing the overall ambiance of any room. The innovative air wash system keeps the glass cleaner for longer, ensuring that the view remains unobstructed by soot. Both models are versatile, suitable for a variety of home styles, and can be adapted for either a wood-burning or multi-fuel option, catering to individual user preferences.

The 8542-P8542 and Clarendon 8541-P8541 models take the experience a step further with advanced burning technology that optimizes air intake, promoting a cleaner burn. This not only increases efficiency but also minimizes environmental impact, adhering to modern eco-friendly standards. The Clarendon series particularly stands out due to its elegant design and range of customizable features, allowing homeowners to tailor their stove to match their specific decor and needs.

The 8543-P8543 offers even higher efficiency ratings, as it incorporates precision-engineered combustion systems that significantly reduce smoke emissions. This model supports an array of installation options, including inbuilt designs that can seamlessly integrate into existing fireplaces, making it a flexible choice for homeowners.

All of these Stovax stoves highlight user-friendly controls for easy operation and precise temperature regulation, ensuring optimal performance at all times. With their combination of artisanal craftsmanship and innovative technology, the 8519-P8519, 8542-P8542, 8517-P8517, Clarendon 8541-P8541, and 8543-P8543 stoves are perfect for creating warmth and a cozy atmosphere in any living space while being environmentally conscious and efficient in energy use. Whether you seek functionality or a visually appealing centerpiece, Stovax offers a range of options tailored to diverse needs and preferences.
Top Page Image Contents