Marmitek SD10 owner manual Carry out the following steps

Page 6

6.Even If you are using more than one smoke detector you only have to register the first one.

7.Press CLEAR to go back to the main menu. Press CLEAR again to quit the menu.

7REGISTERING THE SMOKE DETECTOR WITH THE BASE STATIONS OF THE TYPES MS9470, MS9770, MS9970, SC2200, SC2700, SC2800, PROTECTOR 28

Carry out the following steps:

1.Open the lid on the right side of your security system’s base station.

2.Set the mode switch to the INSTALL position. All indicators of occupied zones will come on.

3.Place the battery (9V) in the battery holder of the smoke detector. (Ensure that the polarity is correct.) The smoke alarm sends a radio signal to the base station: The LED on the sensor will illuminate briefly, the base station emits a short signal tone to confirm.

How to install the battery:

•The smoke detector requires an alkaline battery

•Match terminals on the end(s) of the battery with opposite terminal connectors on th detector. Be sure to insert the alkaline battery in the position shown on the detector.

•When terminals are properly matched, push the battery firmly into place until it snaps and cannot be shaken loose.

4.Even If you are using more than one smoke detector you only have to register the first one.

5.Reset the mode switch to the RUN1 or RUN2 position. Zone indicators will go off.

Now the smoke detector is registered and ready for use.

You can test your system by pressing the test key on the smoke detector for more than 2 seconds.

In the case of fire the smoke detector sends the alarm signal to the Marmitek security system (it does not matter whether the base station is set to arm or disarm. The alarm will be triggered in both cases!)

Your security system will dial the pre-programmed telephone numbers, its siren will sound (depending on your settings), and your lights will be activated.

8REGISTERING THE SMOKE DETECTOR WITH THE BASE STATION OF THE TYPE HOMEGUARD MS8000

Carry out the following steps:

(Every time you press a key you will hear a short confirmation beep)

1.Open the front lid of the HomeGuard MS8000.

2.Enter your current PIN. (Personal Identification Number) If you have never changed this code before, the factory default code is [0000]. You will hear three high tones and one low tone as a confirmation. The green indicator will start flashing.

6

MARMITEK

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Relesswireless Smokesmok Etectordetector SD10SD1 Wireless Smoke Detector SD10 General Information and Function Intended USEFor use with Marmitek security systems of the types SAFETY- and MAINTENANCE- References Installation PlacesInstallation Carry out the following stepsCarry out the following steps Changing the Address of the Smoke Detector Changing the address of the sensorFrequently Asked Questions Final AssemblyChanging the Battery Technical DataDrahtloser Rauchmelder SD10 Gebrauchsanleitung Allgemeine Informationen UND FunktionGeeignet für nachfolgende Marmitek-Sicherheitssysteme Installationsorte UND -HINWEISE AnwendungsbereichSICHERHEITS- UND Wartungshinweise Befolgen Sie nachfolgende Anweisungen Befolgen Sie nachfolgende Anweisungen DIE Adresse DES Rauchmelders Ändern Die Adresse des Rauchmelders ändernOFT Gestellte Fragen Installation BeendenBatterie Auswechseln Technische DatenUtilisation Prévue Détecteur DE Fumée Sans FIL SD10 Guide D’UTILISATIONGénéralités ET Fonction Utiliser avec des systèmes de sécurité Marmitek des typesOÙ Installer LES Détecteurs DE Fumée ? Références DE Sécurité ET D’ENTRETIENExécuter les étapes suivantes « Entrer Code »Exécuter les étapes suivantes Changer L’ADRESSE DU Détecteur DE Fumée Changer l’adresse du capteur12 F.A.Q Foire AUX Questions Assemblage FinalRemplacer LA Pile Données TechniquesGebruik Draadloze Rookmelder SD10 GebruikshandleidingAlgemene Informatie EN Werking De rookmelder heeft de volgende eigenschappenVeiligheid EN Onderhoud PlaatsenInstallatie Volg deze stappen om de Marmitek-rookmelder te installerenVolg de volgende stappen Volg de volgende stappen HET Adres VAN DE Rookmelder Wijzigen Het adres van de rookmelder wijzigenVeel Gestelde Vragen AfmonterenVervangen VAN DE Batterij Technische InformatieDeclaration of Conformity

SD10 specifications

The Marmitek SD10 is an innovative device designed to enhance home entertainment systems through seamless HDMI signal transmission over a long range. This product stands out for its ability to deliver high-definition video and audio with superior quality, making it a favorite among home theater enthusiasts.

One of the key features of the Marmitek SD10 is its ability to support resolutions up to 1080p. This high-definition capability ensures that users can enjoy their favorite movies, games, and television shows in stunning clarity. The device operates on the principle of HDMI over Ethernet, allowing for transmission distances of up to 50 meters, which is impressive compared to traditional HDMI cables that typically have a limited range.

In terms of technology, the Marmitek SD10 utilizes advanced signal compression methods to maintain audio and video integrity over long distances. This ensures that there is minimal lag or distortion, providing a smooth viewing experience without interruptions. The unit is also equipped with a built-in Ethernet switch, which allows users to connect additional devices without needing extra cables.

Another notable characteristic of the SD10 is its plug-and-play design, which makes installation straightforward and hassle-free. Users can simply connect their source device, such as a Blu-ray player or gaming console, to the transmitter, and then connect the receiver to their display, be it a TV or projector. This user-friendly aspect makes it an ideal choice even for those who may not be tech-savvy.

The Marmitek SD10 also features infrared (IR) remote control capabilities, enabling users to operate source devices from the receiver location. This adds an extra layer of convenience, as users can control their media playback without needing to be physically near the equipment.

Additionally, the device is designed to be compatible with various HDMI formats, including 3D video support, ensuring that it meets the demands of modern multimedia content. Its robust build quality and reliable performance make it a worthwhile investment for anyone looking to enhance their home entertainment experience.

In summary, the Marmitek SD10 is a powerful HDMI extender that combines high-definition video and audio transmission with user-friendly features and advanced technology, making it an essential component for modern home theaters.
Top Page Image Contents