X10 Wireless Technology SC1200 Initializing Motion Detectors, Removing Motion Detectors

Page 9

Installation

Initializing Motion Detectors

Remove the cover on the front of the Motion Detector and install 2

AAAalkaline batteries in the compartment. Replace the cover. Press and hold the TEST button on the back of the Motion Detector for 3-4 seconds and then release it. This initializes the Motion Detector and picks a random code that is used when it is registered with the Console. Place the unit face down, so that it won’t see any motion during the registering process below. Note, if the Motion

Detectors you purchased are different from shown here, refer to the installation instructions that came with them.

Registering the Motion Detector with the Console

Press either of the Menu up/down buttons (under the lid to the right of the display). The display then shows ENTER PIN (Personal Identification Number) in the top line.

ENTER PIN 12:00 am

The default PIN is 0000, you’ll find out later (page 24) how you can change this, but for now press 0000 on the keypad (under the lid to the bottom right of the display). This clears the top line and shows * for each number entered.

****

12:00 am

This takes you to the first level of the menu at step 1. This is the INSTALLATION level. The display looks like this:

1. INSTALL

Press OK and the display looks like this:

1.INSTALL ZONE

16

Installation

Now simply press the TEST button on the back of the Motion Detector (or turn the unit over so that it sees motion). The Console will acknowledge that it has been registered by displaying (for example) ZONE 3 SET.

Repeat this for any other Motion Detectors you want to register. The display increments to ZONE 4 SET, etc., as you install more Motion Detectors.

If desired, you can specify what zone you want the Motion Detector to be installed into. Just press the number of the zone you want on the Console’s keypad, before you press the TEST button on the back of the Motion Detector.

Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1 takes you back to the HOME CONTROL screen. Pressing 2 take you up one level of menu.

Removing Motion Detectors

Follow the steps above to install a Motion Detector. When the display shows:

1.INSTALL ZONE

Press the number of the zone you desire (just as if you were going to register the Motion Detector into that zone) but instead of pressing the TEST button on the Motion Detector (to register it) press CLEAR on the Console’s keypad. The display ask you to confirm the deletion:

CLEAR ZONE 1. YES 2. NO

Pressing 1 on the Console’s keypad changes the display to:

1.INSTALL ZONE 13 OUT

Where 13 is the zone you selected. Pressing 2 instead takes you back to the INSTALL ZONE screen.

Press Clear to back out of the menu. You are asked to confirm, 1. YES, 2 NO. Pressing 1 takes you back to the HOME CONTROL screen. Pressing 2 takes you up one level of menu.

17

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model SC1200 Supervised Security SystemRead This First Contents Introduction InstallationLocating Security System components Locating the Security ConsoleSecurity Console Fitting the backup batteriesAttaching cables Mounting the ConsoleInstall Console setup Overview,Sub-menus First Menu LevelInitializing Keychain Remotes Install ZoneRegistering the Keychain Remote with the Console Initializing Door/Window SensorsInstall Zone 13 OUT Installing the Door/Window SensorsRemoving Door/ Window Sensors Clear Zone 1. YES 2. noInitializing Motion Detectors Registering the Motion Detector with the ConsoleRemoving Motion Detectors Installing the Motion Detector Hard-Wired InputsTesting the Motion Detector Setting the phone numbers Setting the ClockRecord Replay Recording your outgoing phone messagePlease Wait Speak NOWChanging your Personal Identification Number PIN Clearing the memoryMemory Clear Setting Options Setting DelaysEntry Delay NEW Timer Setting TimersTimer 12 OFF Unit NumberReplacing Timers Reviewing/Canceling TimersClear Timer Replace TimrIf there’s a problem Using the systemArming the system Disarming the systemWhen there’s an alarm Controlling Lights and AppliancesIf the system is tampered with Optional Lamp Modules Operation from an Outside Telephone General Battery InformationKeychain Remotes Door/Window Sensors and Motion DetectorsProblem Solution TroubleshootingTest Intercom Systems Special NoteLamp Module LM15A Expanding Your SystemXCam2 Camera Ninja Base VCR Commander X10 Wireless CamerasPage SC1200 -12/10 Supervised Security System

SC1200 specifications

The X10 Wireless Technology SC1200 is an innovative wireless home security solution that combines advanced features with user-friendly operation. Designed for homeowners seeking to enhance their security while maintaining convenience, the SC1200 reflects X10's commitment to providing reliable and cutting-edge technology.

One of the key features of the SC1200 is its wireless functionality. Operating on a 310 MHz frequency, the system effectively eliminates the need for complex wiring, making installation straightforward and hassle-free. This wireless capability also allows the user to place sensors and cameras in locations that may be difficult to reach with traditional wired systems, providing more flexibility in designing a tailored security setup.

The SC1200 is equipped with a powerful motion detection system, which uses passive infrared sensors to detect movement within its field of view. This feature ensures that any motion is promptly captured, allowing for immediate alerts sent to the user's smartphone or dedicated receiver. Moreover, the system supports multiple zones, enabling users to customize which areas are monitored and the sensitivity of each sensor, thereby minimizing false alarms.

Another significant characteristic of the SC1200 is its compatibility with X10's extensive range of wireless devices and accessories. Users can enhance their systems with additional motion sensors, door/window sensors, remote controls, and even smart home devices, creating a comprehensive security network tailored to their unique needs. The modularity of the system means that homeowners can easily scale their security measures as desired.

The SC1200 also offers a backup power feature. In case of power failure, the system can continue to operate, ensuring uninterrupted service. This reliability is crucial for any security system, as it guarantees continuous surveillance and peace of mind, even during unforeseen circumstances.

User-friendliness is a priority for X10, and the SC1200 reflects this philosophy with its intuitive interface. The setup process is simplified with clear instructions, making it accessible for users of all technical backgrounds. Additionally, remote access capabilities allow homeowners to monitor their property in real time from anywhere using their smartphones or tablets.

In summary, the X10 Wireless Technology SC1200 presents an effective and versatile solution for home security. With its wireless installation, sophisticated motion detection, compatibility with various devices, reliable backup power, and user-friendly interface, the SC1200 is well-equipped to meet the security demands of modern homeowners, providing both ease of use and peace of mind.
Top Page Image Contents