Home Automation RC-2000 installation instructions Two Speed Heat Pump 3 Stage Heat / 2 Stage Cool

Page 11

Two Speed Heat Pump (3 Stage Heat / 2 Stage Cool)

12

 

UP

HVAC SYSTEM

Dehumidier

(D)

Dehumidifier

11

Humidifier

(H)

Humidifier

10

Compressor Stage 2 (Y2)

Comp Stage 2 Relay

9

Ground Fault

(L)

Fault Relay

8

Fan

(G)

Fan Relay

7

Compressor Stage 1 (Y1)

Comp Stage 1 Relay

6

Energized in Heat

(B)

 

5

Energized in Cool

(O)

Reversing Valve

4

Auxilirary Heat

(W2)

Aux Heat Relay

 

 

 

3

24VAC Common*

(C)

 

1

24VAC "HOT"

(RC)

 

24VAC

THERMOSTAT

CONTROL

TRANSMFOMER

Figure 10 – Connections for two speed heat pump thermostat

CONFIGURATION

￿The “System Type” for this thermostat must be set to “Heat Pump” under “System Options”.

￿The “Cool Stages” and “Heat Stages” settings must be configured under “Stage Settings”.

POWER UP

1.Double check wiring, be sure that there are no stray wires or wire strands at the connections.

2.Connect power to the transformer and system. The display will show the current thermostat settings.

3.Press [FAN] and select “On”. The fan should come on.

4.Press [FAN] and select “Auto”. The fan should go off.

5.Set the Mode to "Heat". Raise the desired heat setting 1 degree above the current temperature. Ensure that the heat pump comes on, in heating mode. Press [HOLD] and select “On” to override Energy Efficient Control. Stage 2 heat should come on.

6.Raise the desired heat setting 3 degrees above the current temperature. Auxiliary heat should come on.

7.After a few minutes, set the mode to "EM Heat". Both stages of the heat pump should stop but the auxiliary heat should remain on. Set the mode to “Off”. Ensure that the auxiliary heat goes off.

8.Press [HOLD] and select “Off” to enable Energy Efficient Control. Set the Mode to "Cool". Lower the desired cool setting 1 degree below the current temperature. Ensure that the heat pump comes on, in cooling mode. Press [HOLD] and select “On”. Stage 2 cool should come on.

9.Set the mode to "Off". Ensure that both stages of the cooling unit go off.

10.Press [HOLD] and select “Off” to enable Energy Efficient Control.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Description InstallationMounting Removing an existing thermostatSlot Tab Base Temperature Sensor Wall Jumper Typical Wiring DiagramsRemove Jumper Power UP ConfigurationZone Controller Two Stage Conventional 2 Stage Heat / 2 Stage Cool About Heat Pump Systems Heat Pump 2 Stage Heat / 1 Stage Cool Two Speed Heat Pump 3 Stage Heat / 2 Stage Cool HAI Home Control Systems Remote System Wiring DiagramsOther Systems Remote Setback SwitchThermostat Remote Temperature SensorInstallation Settings Type Program ModeSystem Options SystemCool Minimum Off Stage SettingsCool/Heat Min On/Off Cool Minimum OnHeat Pump 2 Cool / 3 Heat Temperature SensorsEEC Dehumidifier Output Humidifier Output Factory DefaultLimited Warranty Humidity OptionsSymptom Action to Take Troubleshooting Tips Symptom Action to Take
Related manuals
Manual 20 pages 59.46 Kb

RC-2000 specifications

Home Automation RC-2000: A Smart Revolution in Home Management

The Home Automation RC-2000 is an innovative solution designed to bring convenience, security, and efficiency to modern living. This advanced system enables homeowners to seamlessly control a variety of devices within their homes, providing a comprehensive ecosystem that enhances everyday life.

One of the standout features of the RC-2000 is its compatibility with a wide range of smart devices. From lighting and temperature control to security systems and entertainment equipment, the RC-2000 integrates effortlessly with countless devices, allowing users to manage their entire home through a single interface. This compatibility is made possible through its support for multiple communication protocols such as Wi-Fi, Zigbee, Z-Wave, and Bluetooth.

The RC-2000 also excels with its user-friendly mobile app. This intuitive application enables users to monitor and control their home from virtually anywhere, whether inside or outside the house. Customization options within the app allow homeowners to create schedules, set scenes, and automate tasks, making it easy to tailor the system to their unique needs.

Another notable characteristic of the RC-2000 is its advanced security features. Users can set up real-time monitoring and receive alerts for unusual activities in and around their homes. This capability is complemented by integration with smart cameras and locks, ensuring that users can remotely manage their home security with confidence.

The system’s voice control functionality further enhances user experience, as it can be easily integrated with popular virtual assistants like Amazon Alexa, Google Assistant, and Apple HomeKit. This hands-free control allows for seamless interaction with the system, enabling users to adjust settings or command devices through simple voice commands.

Energy efficiency is also a key focus of the RC-2000, as it not only promotes convenience but also aids in reducing energy consumption. Smart thermostats, for instance, can learn user patterns and adjust heating and cooling accordingly, leading to significant savings on energy bills.

With its combination of advanced technologies, comprehensive features, and user-friendly interface, the Home Automation RC-2000 stands at the forefront of smart home solutions. It is designed to provide homeowners with peace of mind, ultimate control, and the enhanced convenience that comes from a truly connected environment. The RC-2000 is not just a gadget; it is a gateway to a smarter, more efficient home.
Top Page Image Contents