Samsung LH55OHFPKBC/EN Automatic Open Network Settings Wired, Manual Open Network Settings Wired

Page 84

Set the network connection to use Internet services such as perform software upgrades.

Automatic Open Network Settings (Wired)

Connect to the network using a LAN cable.

Make sure a LAN cable is connected first.

How to set up automatically

1Set Network type to Wired from the Open Network Settings page.

2Press the Connect button to start Open Network Settings.

‒‒ The Connect button is only enabled when the LAN cable is properly connected.

3The network test screen appears and verifies the network connection.

When the connection has been verified, the “Wired network and Internet connection completed.” message appears.

――If the connection process fails, check the LAN port connection.

――If the automatic process cannot find the network connection values or if you want to set the connection manually, go to the next section, network setup.

Manual Open Network Settings (Wired)

Offices may use static IP addresses.

If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server address. Enter these values manually.

Getting the Network Connection Values

To view the Network connection values on most Windows computers, follow these steps.

1Right click the Network icon on the bottom right of the screen.

2In the pop-up menu that appears, click Status.

3On the dialog that appears, click the Support tab.

4On the Support Tab, click the Details button. The Network connection values are displayed.

How to set up manually

1Set Network type to Wired from the Open Network Settings page.

2Press the Connect button to start Open Network Settings.

‒‒ The Connect button is only enabled when the LAN cable is properly connected.

3The network test screen appears and the verification process starts. Press Stop. The verification process stops.

4Select IP Settings on network connection screen. The IP Settings screen appears.

5Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry process for each field in the IP Address.

――Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.

6When done, select OK at the bottom of the page, and then press E. The network test screen appears and the verification process starts.

7When the connection has been verified, the “Wired network and Internet connection completed.” message appears.

84

Page 83 Page 85
Image 84
Page 83 Page 85
Contents OH46F I OH55F Table of contents Screen Adjustment Support Appendix Before Using the Product Safety PrecautionsCleaning StorageElectricity and Safety Installation Operation Page Preparations Checking the ComponentsComponents Parts PartsParts Description Remote sensorReverse Side Port DescriptionAnti-theft Lock To lock an anti-theft locking deviceRemote Control VOLTo place batteries in the remote control Hdmi 1 and HdmiIt sets safe lock function Installation on a Perpendicular Wall Tilting Angle and RotationVentilation Installation on an Indented Wall Minimum 40 mm Ambient temperature Under 50CPlane view Installing the Wall Mount Installing the Wall Mount KitWall Mount Kit Specifications 995 x 500 39.2 xRemote Control RS232C Pin SignalCable Connection RS232C CablePin No Standard Colour Signal Connector 9-Pin D-Sub to Stereo CableLAN Cable GndConnector RJ45 SignalDirect LAN cable PC to HUB Cross LAN cable PC to PCConnection ConnectionViewing control state Get control command Controlling Set control commandCommand Command type Value rangePower control Volume controlERR a code showing what error has occurred Input source control 0x220x23 0x24Screen mode control Screen size controlFunction Video Wall Mode Control Safety Lock OnFull Natural Video Wall On Video Wall User Control10x10 Video Wall Model Off10x10 Video Wall Model 1 ~ WallSNo Product Number code assigned to the productConnecting and Using a Source Device Before ConnectingPre-connection Checkpoints Before connecting cables JackConnecting to a PC Connection Using an HDMI-DVI CableConnection Using an Hdmi Cable Connecting to a Video Device Using an Hdmi cable or Hdmi to DVI Cable up to 1080pConnecting the HDBase-T LAN CableConnecting to an Audio System Connecting the LAN CableChanging the Input source SourceEdit MagicInfo S / URL Launcher / Web BrowserSettings Web BrowserGeneral Search EnginePrivacy & Security Blocked PagesApproved pages Refresh Options Using MDC MDC Programme Installation/UninstallationSelect MDC Unified from the list and click Change/Remove Connecting to MDC Using MDC via RS-232C serial data communications standardsUsing MDC via Ethernet Connection using a direct LAN cableConnection using a cross LAN cable Player feature Viewing contentPlayer No.DescriptionWhen content is running Available menuControl buttons on the remote Button FunctionFile Formats Compatible with Player Network Schedule MultiframeTemplate files and LFD.lfd files Contents Video Audio Power Point WordTemplate files LFDView a thumbnail image and brief information of the content ScheduleNo. Description Home → Schedule → Enter ESelect Export to export the settings Clone ProductClone Product Home → Clone Product → Enter EID Settings ID SettingsDevice ID Device ID Auto SetVideo Wall Video WallHorizontal x Vertical Screen PositionFormat Network Status Network StatusCheck the current network and Internet connection Home → Network Status → Enter EPicture Mode Picture ModeOn/Off Timer On TimerOn/Off Timer Home → On/Off Timer → Enter EOff Timer Holiday ManagementTicker TickerHome → Ticker → Enter E URL Launcher URL LauncherHome → URL Launcher → Enter E URL Launcher Settings URL Launcher SettingsHome → URL Launcher Settings → Enter E Approving a connected device from the server Setting the current time Select Time ZoneScreen Adjustment Menu m → Picture → Picture Mode → Enter EPicture Menu m → Picture → Enter E Colour Temperature Colour Temperature 16000KWhite Balance PointGamma Calibrated valueGamma Calibrated value Dont applyAdvanced Settings Enable to optimise picture quality for Hdmi UHD connection Hdmi UHD ColorMotion Lighting HDMI1 Off / On HDMI2 Off / OnDigital Clean View Picture OptionsColour Tone Picture OptionsFilm Mode Hdmi Black LevelDynamic Backlight Auto / Low / NormalPicture Size Picture SizeFit to Screen Zoom/PositionReset Picture Reset PicturePicture Off Picture OffSource Content Orientation OnScreen DisplayDisplay Orientation Onscreen Menu OrientationScreen Protection Auto Protection TimeScreen Burn Protection Screen ProtectionTimer Pixel Shift Timer Immediate displayScreen Burn Protection OffTimer Immediate display Off Pixel ShiftOff / Pixel / Rolling bar / Fading screen No Signal Message Message DisplaySource Info MDC MessageReset OnScreen Display Reset OnScreen DisplayLanguage OnScreen DisplayOpen Network Settings NetworkNetwork type Network Settings Wired Connecting to a Wired NetworkAutomatic Open Network Settings Wired Manual Open Network Settings WiredNetwork Setting Wireless Set Network type to Wireless from the Open Network SettingsManual Network Setup Wireless How to set up using Wpspbc If your router has a Wpspbc button, follow these stepsServer Network Settings Wi-Fi Direct Access Notification Mobile Device ManagerDevice Name Mobile Device ListAccessibility SystemMenu Transparency High ContrastStart Setup Menu m → System → Start Setup → Enter ENTP Settings Sleep TimerPower On Delay TimeAuto Source Switching Auto Source SwitchingPrimary Source Recovery Primary SourcePower Control Auto Power OnMax. Power Saving Power ControlPower Button Network StandbyEco Solution Energy Saving ModeEco Solution Brightness LimitNo Signal Power Off Auto Power OffScreen Lamp Schedule Screen Lamp ScheduleFan and Temperature Fan Speed SettingOutdoor Mode Temperature ControlInput Device Manager Play via100 Change PIN 101Change PIN Menu m → System → Change PIN → Enter ESecurity 102General 103Smart Security General104 Anynet+ HDMI-CECProblem Possible Solution 105On again System menu106 Hdmi Hot PlugCustom Logo Reset System Game ModeReset System Menu m → System → Reset System → Enter ESoftware Update Reset AllSupport Contact SamsungTroubleshooting Guide Testing the ProductChecking the Resolution and Frequency 109Installation issue PC mode Screen issue110 Check the followings111 Remote control issue Source device issueOther issue Resolution is not supported. appearsThere is no sound in Hdmi mode 113IR sensor is not functioning How can I change the resolution? 114Question Answer How can I change the frequency?How do I set powersaving mode? 115Question Specifications 116Model Name Preset Timing Modes 117Model Name OH46F / OH55F 118 Responsibility for the Pay Service Cost to Customers Appendix119 What is afterimage burn-in? Optimum Picture Quality and Afterimage Burn-in Prevention120 Optimum Picture Quality121 Preventing afterimage burn-in‒‒ Move and change text every 30 minutes as shown below Licence 122Terminology 123
Related manuals
Manual 123 pages 43.5 Kb Manual 123 pages 19.92 Kb Manual 123 pages 40.57 Kb Manual 123 pages 4.72 Kb Manual 106 pages 22.27 Kb Manual 106 pages 12.52 Kb Manual 106 pages 7.27 Kb Manual 2 pages 58.8 Kb Manual 123 pages 104 b Manual 123 pages 39.31 Kb Manual 123 pages 34.93 Kb Manual 106 pages 58.74 Kb Manual 123 pages 45.91 Kb

LH55OHFPVBC/EN, LH46OHFPKBC/EN, LH55OHFPVBC/XV, LH55OHFPKBC/EN specifications

Samsung is a leading name in the display technology sector, and its range of professional displays, including the LH46OHFPKBC/EN, LH55OHFPKBC/EN, and LH55OHFPVBC/EN models, exemplifies innovative design, exceptional quality, and advanced functionality.

The LH46OHFPKBC/EN is a 46-inch display tailored for various commercial applications. It features a Full HD resolution of 1920 x 1080 pixels, which ensures sharp and vibrant image quality. This model stands out due to its slim and lightweight design, making it easy to install in diverse environments such as retail spaces, corporate offices, and public venues. With a brightness of 700 nits, it is well-suited for brightly lit areas, ensuring visibility without strain.

The LH55OHFPKBC/EN, a 55-inch variant, offers similar specifications with added benefits. It also provides Full HD resolution and remarkable brightness levels, making it ideal for engaging audiences and attracting attention. This model is equipped with Samsung’s proprietary MagicINFO software, facilitating easy content management and scheduling for digital signage. Its multiple input options ensure compatibility with various sources, enabling seamless integration into existing systems.

Another impressive model, the LH55OHFPVBC/EN, features advanced technologies to cater to a diverse range of applications. It includes high dynamic range (HDR) support, which enhances the contrast and color accuracy, providing an immersive viewing experience. This model is designed to operate continuously, boasting a robust build that withstands rigorous use in demanding environments.

All three models incorporate Samsung's exceptional durability standards, evidenced by their IP55 rating, which signifies protection against dust and water, enhancing their resilience for outdoor usage. They also support an array of mounting options, allowing for flexible installation tailored to specific site requirements.

In terms of connectivity, Samsung's displays feature versatile ports, including HDMI, DisplayPort, and USB, ensuring users can connect a wide range of devices effortlessly. The built-in speakers further enhance the multimedia experience, making these displays suitable for presentations and interactive installations.

In summary, the Samsung LH46OHFPKBC/EN, LH55OHFPKBC/EN, and LH55OHFPVBC/EN combine cutting-edge technology with robust design, rendering them ideal for businesses seeking high-quality, reliable display solutions. Their features make them an excellent choice for anyone looking to enhance visibility and engagement in any commercial setting.
Top Page Image Contents