Lightolier 1104FESR Close-In Fig. D, Airseal Installation optional, Snap-On Fig. E

	Instruction Sheet Number  1104FES
Page of 2	Installation Procedure for Convertible IC/Non IC Frame-In-Kits

4.Close-In (Fig. D)

Install plasterboard or other dry type ceiling. Hole in board can be cut either on the floor or after the board is secured to the ceiling using housing opening as cutting guide. Housing is secured by 3 screws which allow adjustment for variable ceiling thicknesses.

5.Airseal® Installation (optional)

Option 1: Install LAS56 Flange Gasket Kit (available separately).

Option 2: Install a bead of silicone caulking compound between the ceiling opening and edge of HOUSING. Housings are tested in accordance with ASTM E 283 (max 2 cfm @ 75 pa) and comply with WSEC & MEC when installed as instructed. NOTE: If factory installed tape or knockouts are removed from vertical adjustment slots in housing wall LAS56 Flange Gasket Kit must be used (available separately).

6.Snap-On (Fig. E)

Important - Insert socket Holder in neck of reflector making sure spring tabs fully engage into slots in reflector.

7.Push-Up (Fig. F)

Push reflector trim straight up until }

it is tight against ceiling.See Separate

8.To remove trim (Fig. G):Reflector Trim

• Turn off power to fixtureInstruction Sheets

•Remove lamp

•Squeeze reflector spring from inside until the trim disengages.

•To retrieve socket Holder, pull on one of the socket spring legs to disengage.

9.Ballast Replacement (Fig. H)

NOTE: Ballast replacement must be performed by a “qualified electrician.” 1. Turn power off.

2. DO NOT CUT WIRES. Release all wires from BALLAST WIRE CONNECTORS by inserting small blade tool with insulated handle into

WIRE RELEASE SLOTS.

NOTE: Ballast Kits generally are supplied with this special wire release tool. 3. If Ballast is not equipped with push-in wire connectors, disconnect

Ballast from socket wires by removing wire nuts (4).

TWO (2) YEAR LIMITED WARRANTY Exclusively For Energy Star®‚ Qualified Luminaires: Lightolier warrants to you, the original purchaser, for a period of two years from the date of original retail purchase, this product to be free from defects in materials and workmanship, when properly installed and under normal conditions of use. Lightolier, at its sole option, will repair or replace, free of charge, any Lightolier product found defective in workmanship or materials. The purchaser is responsible

for any costs associate with removal and re-installation of the product and shipping to and from the manufacturer.

For warranty claims on defective ballasts within the said two-year period, Lightolier will provide a replacement ballast of identical type and function (but not necessarily brand name) free of charge. Lightolier is not responsible for any costs incurred to physically replace the ballast in the light fixture. Ballast manufacturer's warranties may extend beyond a two-year time period. For defective ballast claims outside the Lightolier warranty period, please contact the ballast manufacturer per the informa- tion noted on the ballast label.

THE MANUFACTURER LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH ABOVE, AND OTHERWISE DISCLAIMS ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS. Some states disallow certain limitations on implied warranties, so you should consult your state law if you have a question regarding this Limitation and disclaimer. The manufacturer disclaims any and all liability for incidental, consequential, special or indirect damage arising out of any claimed breach of warranty or otherwise. However, some states do not allow exclusion or limitation of such damages, so this disclaimer may not apply to you. The remedy provided in this Limited Warranty for defective products is the purchaser's sole and exclusive remedy, subject to your state law. Further, this Warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state.

No agent, employee or representative of Lightolier has any authority

to bind Lightolier to any affirmation, representation or warranty concerning goods sold by Lightolier except as specifically included herein.

For all warranty claims, please call Lightolier at (866) 660-5483.

PROVIDE THIS WARRANTY TO THE END USER.

END USER SHOULD RETAIN THIS DOCUMENT FOR WARRANTY RECORDS.

squeeze clip
Squeeze to adjust,	Deform Material Here
release to lock	for Additional Lock

mounting bar

For Tight Spaces: Mounting bar channels

can be shortened and used as nailing legs in tight spaces.

Simply remove inner bar

from holed channel, bend channel at appropriate point and use extra screw to secure it to the joist. (Fig. D)

socket

reflector spring

Socket Spring

Fig. G

Remove Trim

		REMovE	INSERT
Fig. H
Ballast			WIRE RELEASE
Replacement			bLAdE
			(by oThERS)
			WIRE RELEASE
			SLoTS
			bALLAST WIRE
			CoNNECToRS
			LAMP
		REd
NuETRAL		REd
(WhITE)	bALLAST	bLuE
hoT		bLuE
(bLACK)
GRouNd
			U.S. and Foreign
			Patents Pending

Lightolier a Genlyte companywww.lightolier.com 631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2005 Genlyte Group LLC • C1205