Samsung LC49HG90DMMXCH, LC49HG90DMUXEN, LC49HG90DMEXXV, LC49HG90DMIXCI manual

Page 15

Note

1The supported USB disk formats are FAT, FAT32, and NTFS.

2For the CHG90 model, make sure that each upgrade file is a BIN format file, follows the CHG90 model naming rule (m-HG949CCAA-****.*[4 digits].bin, where ****.* is a version number, and 4 digits are a checksum. For example, “m-HG949CCAA-1000.0[6E80].bin” complies with the naming rule for the CHG90 model.), and must be copied to the root directory.

3Make sure that the USB disk only contains one upgrade file for each model, and then follow the instructions in this guide.

4If you want to revert or downgrade to a lower version, change the file name as m-HG949CCAA-0000.0[4 digits], and then take the same steps.

5If the No valid update files found. Please check your USB device and try again. message is displayed, this is probably due to the following reasons.

‒‒ No USB disk is inserted into the USB 1 port. ‒‒ The USB disk format is not supported.

‒‒ The USB disk contains no valid upgrade files. (No upgrade files exist, or the file names are incorrect.)

6Do not turn off the monitor. And prevent the upgrading from any interruption as far as possible. If an interruption happens, the monitor will return to the production version.

――Note that the production version may not be the same as the version before this upgrading if some other upgrading has been done earlier.

15

Image 15

Contents

Gaming Monitor Table of contents OnScreen Display Precautions for storage Before Using the ProductSecuring the Installation Space Safety PrecautionsElectricity and Safety CleaningInstallation Operation Page Preparations PartsControl Panel Pressenter The selected item will be applied Function Key GuideGame Setting Key Changing Brightness, Contrast and Sharpness settings Changing the Volume settingConnect to a USB device Reverse SideUpgrading the Software via USB Power OffPage +4˚ Adjusting the Product Tilt and HeightTo lock an anti-theft locking device Anti-theft LockAttaching the Stand Type one InstallationAttaching the Stand Type two Lift the COVER-REAR TOP Disassemble the COVER-REAR TOP Removing the Stand For Attaching the Bracket WallAlign B with Attaching the Bracket WallConnection Using the DP Cable Connecting and Using a Source DeviceConnecting and Using a PC Connection Using the Hdmi CableConnection Using the Audio Cable Connection Using the Mini DP CableConnecting to Headphones Connecting to MicrophoneUtilizing the Product as a USB HUB Connecting a PC to the ProductPower Connecting the PowerDirection as shown in the figure Headphones hanger Downward UpwardTidying Up the Connected Cables Arrange the cables against the bendDriver Installation Setting Optimum ResolutionCorrect posture to use the product Game Picture ModeResponse Time Adjust the brightness of the dark areasRefresh Rate Black EqualizerFreeSync How do you enable FreeSync?Low Input Lag Screen SizeSelect the best screen size and ratio Game Setting Key Save SettingsPicture Sharpness Adjust the tint of the screenBrightness ContrastCalibration Report Eye Saver ModeScreen Adjustment Hdmi Black LevelConfiguring the PBP Settings PBP ModeSelect the input source you want to watch on screen1 Aspect RatioScreen1 Screen2Set the menu language OnScreen DisplayLanguage Display TimeLocal Dimming VolumeSystem LightingUSB Super Charging Off TimerPC/AV Mode Eco Saving PlusDisplayPort Ver Hdmi ModePower LED On Reset AllHDR InformationPre-requisite to the use of HDR System Requirements Installing the SoftwareEasy Setting Box Restrictions and Problems with the InstallationCheck that the power cable is connected properly Troubleshooting GuideTesting the Product Checking the Resolution and FrequencyCheck the cable connection to the product Change the Color settingsSet the frequency on your graphics card General SpecificationsStandard Signal Mode Table 66.000 60.000 453.000144.000 Not a product defect Responsibility for the Pay Service Cost to CustomersProduct damage caused by customers fault Appendix

Related manuals