Lightolier VRA2G16LS26U dimensions Options & Accessories, Specifications

SECTION 2/Folio G05-50 REV. A

	VR PARABOLIC VRA2G16LS26U
Page 2 of 2	2'x2' RECESSED FLUORESCENT, 4" DEEP, 16 CELL (4x4) PARABOLIC LOUVER
	STATIC OR AIR SUPPLY/RETURN, IES RP1 FOR NORMAL VDT USE

PHOTOMETRY

	LER = FP - 42.0				IW - 57.6			BF - 90.3
MODEL NO. VRA2G16LS26U Comparative yearly lighting energy cost per 1000 lumens = $5.71
		coefficients of utilization — zonal cavity method									(effective floor cavity reflectance 0.20)
			RF		20						20					20
			RC		80						50					30
			RW	70	50		30		50		30	10			50	30	10
			1	58	57		55		53		52	51			51	51	50
		ratio	2	55	52		49		49		47	46			48	46	45
			3	51	47		44		45		43	41			44	42	40
		cavity	4	48	44		40		42		39	37			41	38	36
			5	45	40		37		39		36	33			38	35	33
		room	6	42	37		33		36		33	30			35	32	30
			7	40	34		31		33		30	28			32	30	28
			8	37	32		28		31		28	25			30	27	25
			9	35	29		26		29		26	23			28	25	23
			10	33	27		24		27		24	22			26	24	22
		visual comfort probability					(rated lumens per lamp 3150.)
			room size					ceiling height						ceiling height
		W		L			8.5	10.0	13.0	16.0			8.5	10.0	13.0		16.0
	20			20			95	93	90	82			99	98	98		95
	20			30			96	94	91	85			99	99	98		96
	20			40			96	94	93	87			99	99	98		96
		20		60			96	94	93	88			99	99	98		96
	30			20			95	93	92	86			99	98	98		95
	30			30			96	95	93	87			99	99	98		96
	30			40			96	95	94	89			99	99	98		96
	30			60			96	95	94	90			99	99	98		96
		30		80		lengthwise	96	94	94	90		crosswise	99	99	98		96
	40			40			96	95	94	90			99	99	98		96
	40			20			95	94	92	86			99	99	98		96
	40			30		luminaries	96	95	93	88		luminaries	99	99	98		96
	40			60			96	94	94	91			99	99	98		96
	40			80			96	94	94	91			99	99	98		96
		40		100			96	94	94	91			99	99	98		97
	60			30			96	95	93	88			99	99	98		96
	60			40			96	94	94	90			99	99	98		96
	60			60			96	95	94	91			99	99	98		97
	60			80			96	95	94	91			99	99	98		97
		60		100			96	95	94	91			99	99	98		97
	100			40			96	94	94	90			99	99	98		97
	100			60			96	95	94	91			99	99	98		97
	100			80			96	95	94	91			99	99	98		97
		100		100			96	95	94	91			99	99	99		97

ORDERING INFORMATION

Explanation of Catalog Number. Example: VRA2G16LS26U120SORF

VR 2 16 S 2

6U

	BODY STYLE:		CEILING TYPE:		LOUVER		LAMP
	A=Air Handling		G= Grid		FINISH*:		QUANTITY
	S=Static		(lay-in T bar)		L=Low
			F=Flanged		Iridescence
VR:		FIXTURE	(overlap)	NUMBER OF	Semi-specular	SINGLE “V”
4" Deep		WIDTH	Z spline and	CELLS:	(standard)	REFLECTOR
Pre-anodized			plaster	(4 rows of	P=Low
Aluminum				4 cells)
			frame		Iridescence
Louver
			T=Slot grid or		Specular
For Normal

VDT Use	two-directional
	concealed
	T (see options)

LAMP TYPE/

FIXTURE

LENGTH: 6"U Lamp

T8 OR T12

(Nominal 24")

VOLTAGE:			OPTIONS:
120 or 277			Add appropriate
			suffix to catalog
			no, ie: (GLR)
	BALLAST TYPE:
1-2	Lamp Mag. T12		LE	<10THD
		<20THD
1-2	Lamp Elec. T8		SO*	HI*
LOL T8 Dimming			PS	–

*Instant Start Standard

Other dimming options. Consult factory.

OPTIONS & ACCESSORIES

PLASTER FRAME: Catalog Number: PF22.

CONTINUOUS ROW INSTALLATION: For F type fixtures, half-width flanges are

required between fixtures, Order Catalog Number: S2CTRIM (each joint).

SPLAY TRIM: For T ceiling type only. SUFFIX: CTZ22 S2 SPLAY TRIM.

RADIO INTERFERENCE FILTER: 120 or 277 volt, 50 or 60 Hz. One per fixture

standard. SUFFIX: RF.

ELECTRICAL WIRING OPTIONS: Consult factory.

AIR CLOSURE STRIPS: SUFFIX ACS2 (factory installed).

DRYWALL KIT: Order Catalog Number: FK92X2. (Request Folio OA30-10.)

CHICAGO PLENUM: SUFFIX: CP.

SPECIFICATIONS

PERFORMANCE: In an installation of 2 lamp 31W luminaires in a room cavity ratio of 1, reflectance 80% ceiling, 50% wall, 20% floor, the C.U. shall not be less than .57 with a spacing to mounting ratio of 1.2 perpendicular to the lamps. To meet IES RP1 preferred requirements for VDT areas the VCP (visual comfort proba- bility) shall not be less than 96 either crosswise or lengthwise and the maximum average brightness at 65°, 75° and 85° shall not exceed 293, 104, and 77 cande- las per square meter respectively in the 0°, 45°, and 90° horizontal planes. Candelas at Nadir (0°) not to exceed 1737.

SPECIFICATIONS (continued)

AIR HANDLING: (VRA only) side air passages for air supply or air return. Optional side closure strips. Air return is also provided through the lamp com- partment through fixture body ends.

MATERIALS: Chassis parts are die-formed code gauge cold rolled steel. Housing side rails hemmed over and housing ends turned-in for safe handling. Louver is pre-anodized aluminum (Coilzak® or equal).

FINISH: Chassis exterior–black baked polyester enamel. Cavity–white baked polyester enamel minimum 86% reflectance. Phosphate undercoating. Louver–low iridescence semi-specular anodized vertical grain aluminum reflec- tor sheet is standard.

ELECTRICAL: Thermally protected class “P” ballast C.B.M. approved, non PCB. If K.O. is within 3" of ballast, use wire suitable for at least 90°.

LABELS: I.B.E.W./UL and C-UL.

Job Information	Type:
Lightolier a Genlyte Thomas Company	www.lightolier.com

Technical Information: (978) 657-7600 • Fax (978) 658-0595

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2002 Genlyte Thomas Group LLC (Lightolier Division) A0902