UH-10 Handheld Microphone, Instrument Use

UH-10 HANDHELD MICROPHONE

1.Unscrew the BATTERY COMPARTMENT COVER (19) and remove, exposing the BATTERY HOLDER (20). Insert a fresh 9V ALKALINE BATTERY (21), observing the correct polarity as marked, and screw the cover back on to the microphone. Make sure the cover is screwed on completely. A fresh alkaline battery can last up to 10 hours in use, but in order to ensure optimum performance, it is recommended that you replace the battery after every 7-8 hours of use.

2.Turn on the UH-10 by sliding the OFF/STANDBY/ON SWITCH (22) to the STANDBY position (transmitter on, audio muted) or the ON position (transmitter and audio both on). The BATTERY INDICATOR LED (23) will give a single quick flash, indicating usable battery strength. In the case of a dead or low battery, the LED will either not go on at all or will stay on continuously, indicating that the battery should be replaced with a fresh one. To preserve battery life, turn the transmitter off when not in use.

3.The microphone is now ready to use. The A and/or B DIVERSITY LED INDICA- TORS (3) and most or all of the RF LEVEL DISPLAY LEDs (4) on the URR-10 receiver should now be lit, indicating a received signal from the transmitter. When ready to speak, slide the transmitter switch to the ON position. Adjust the volume of the receiver as per the Audio Output Microphone Connection section of the above URR-10 receiver instructions. [Note: Observe care in selecting P.A. volume, transmitter location and speaker placement so that acoustic feedback (howling or screeching) will be avoided.]

21 20

19.BATTERY COMPARTMENT COVER

20.BATTERY HOLDER

21.9V ALKALINE BATTERY

22.OFF/STANDBY/ON SWITCH

23.BATTERY INDICATOR LED

UB-10 BODYPACK TRANSMITTER

1.Slide open the hinged BATTERY COMPARTMENT (24) and insert a fresh 9V ALKALINE BATTERY (25), observing the correct polarity. A fresh alkaline battery can last up to 10 hours in use, but in order to ensure optimum performance, it is recommended that the battery be replaced after 7-8 hours of use.

2.The UB-10 is equipped with an INPUT SELECTOR SWITCH (26) in the battery compartment for selecting the type of audio input you will be supplying to the transmitter. Select from the choice of three positions: INSTRUMENT (for guitar, bass, etc.)/ HEADWORN MIC/ LAVALIER MIC.

3.The UB-10 is provided with a 3.5 mm LOCKING JACK (27) for connecting the audio input selected. Connect either the INSTRUMENT CORD (28) or the HEADWORN MIC (29) or LAVALIER MIC CORD (30) as desired, according to the input selected. (Note: Use only the input audio source as per the input selected with the AUDIO INPUT SELECTOR SWITCH or the audio will not be optimal–a muddy or distorted sound may result.) To secure the connection, turn the slip ring on the plug clockwise to thread it on the jack. To unplug, reverse the process. Slip the transmit- ter into a pocket or use CLIP (34) to attach it to your clothes or instrument strap (if using the UB-10 as an instrument transmitter).

4.Turn on the UB-10 by sliding the OFF/STANDBY/ON SWITCH (31) to the STANDBY position (transmitter on, audio muted) or the ON position (transmitter and audio both on). The BATTERY INDICATOR LED (32) will give a single quick flash, indicating usable battery strength. In the case of a dead or low battery, the LED either will not go on at all or will stay on continuously, indicating that the battery should be replaced with a fresh one. To preserve battery life, turn the transmitter off when not in use. The transmitter is now ready to use. The A and/or B DIVERSITY LED INDICATORS (3) and most or all of the RF DISPLAY LEDs (4) on the URR-10 receiver should now be lit, indicating a received signal from the transmitter.

5.Instrument Use

Plug the 1/4" phone plug from the INSTRUMENT CORD (28) into the instrument. As the cord to the instrument also serves as the antenna, be sure to extend it fully for maximum range. Rolling up or shortening the cord may reduce the effective operating range. When ready to play, slide the audio OFF/STANDBY/ON SWITCH (31) to the ON position. Adjust the volume of the receiver as per the Audio Output Instrument Connections section of the above URR-10 receiver instructions. For optimum performance, an INPUT LEVEL CONTROL (33) is provided on the top panel of the UB-10. Adjust the gain by turning the control with your thumb. For instrument use, it is recommended that this control be turned to maximum gain. However, for ultra high-gain instrument sources such as active bass pickups or even extra hot guitar pickups, turning the level down slightly will create a cleaner sound. (Note: Turning down the input gain too much can compro mise the signal-to-noise ratio and is not recommended. Set for the maximum possible gain and headroom without noticeable distortion on the high level peaks).

UB-10 specifications

Nady Systems UB-10 is a versatile and compact wireless microphone system designed for a range of applications, making it an ideal choice for musicians, public speakers, and audio professionals. With a focus on delivering high-quality audio transmission, the UB-10 highlights advanced technologies and user-friendly features that enhance performance and reliability.

One of the standout features of the UB-10 is its UHF frequency range. This allows for a more stable signal transmission compared to VHF systems, significantly reducing the risk of interference from other wireless devices. The UB-10 operates in the UHF bands, providing users with a selection of frequencies to choose from, ensuring clear audio quality even in crowded environments.

A key characteristic of the UB-10 is its lightweight and portable design. The system's bodypack transmitter is designed for ease of use and can be comfortably worn during performances or presentations. The durable construction ensures it can withstand the rigors of frequent use, making it a reliable option for traveling performers or mobile presenters.

The UB-10 also features a built-in rechargeable battery that offers extended use time. This sustainability aspect minimizes the need for disposable batteries and encourages environmentally friendly practices. The transmitter and receiver provide visual indicators for battery status, allowing users to monitor battery life easily.

Another important technology in the UB-10 is its automatic frequency scanning capability. This feature detects and selects the cleanest frequency available, simplifying setup and operation. Users no longer have to spend excessive time tuning their systems manually, allowing them to focus on their performance or presentation.

Additionally, the UB-10 includes a variety of output options, enabling easy connectivity with different audio systems, including mixers and amplifiers. The receiver provides both XLR and 1/4” outputs, making it versatile enough for studio and live sound applications.

In conclusion, the Nady Systems UB-10 wireless microphone system stands out for its robust performance, user-friendly features, and technological advancements. With its UHF frequency reliability, portable design, rechargeable batteries, automatic scanning, and versatile output options, it serves as an excellent choice for anyone in need of a dependable wireless audio solution. Whether for live music, theater, or public speaking events, UB-10 fulfills the demands of modern audio professionals with ease.