Samsung AR24KQFHCWKNMG, AR24KRFHCWKNMG, AR18KRFHCWKNMG Final check and trial operation, English-51

Page 51

Final check and trial operation

To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly.

Check the followings:

•Strength of the installation site

•Tightness of pipe connection to detect gas leak

•Electric wiring connection

•Heat-resistant insulation of the pipe

•Drainage

•Grounding conductor connection

•Correct operation (follow the steps below)

1. Press the Power button and check the following:

The indicator on the indoor unit lights up.

The airflow blade opens and the fan gears up for operation.

2. Press the Mode button to select Cool or Heat mode.

In Cool mode, use Temp hr. + or – button and set the temperature at 16 °C.

In Heat mode, use Temp hr. + or – button and set the temperature at 30 °C.

• Approximately 3~5 minutes later, outdoor unit will start to operate and the

Cool or Warm air will blow out.

• After 12 minutes of stationary condition check the indoor unit air treatment.

Cooling mode (indoor unit check) Inlet air temp. - Outlet air temp: From 10 °C to 12 °C (indicative delta T)

Heating mode (indoor unit check) Outlet air temp. - Inlet air temp: From 11 °C to 14 °C (indicative delta T)

In heating mode, the indoor fan motor can remain off to avoid cold air blown into conditioned space.

3.Press the Air swing button and check the following:

The airflow blades work properly.

4.Press the Power button to stop the operation.

• When you complete the installation successfully, hand over this manual to the user for storage in a handy and safe

place.

Pump down procedure (when removing the product)

1.Turn on th air conditioner and select Fast Cool mode. Please let the compressor run for more than 5 minutes. If the compressor does not operate for more than 5 minutes due to protection control, wait about 2 minutes, and then carry out the next procedure.

2 . Release the valve caps on High and Low pressure side.

3 . Use L wrench to close the valve on the high pressure side.

4 . After approximately 1 minutes, close the valve on the low pressure side.

5 . Stop operation of the air conditioner by pressing the Power button on the indoor unit or remote controller.

6 . Disconnect the pipes.

English-51

07stIn llan atio

MG_BORACAY_IB&IM_EN_DB68-05789A-00.indd 51

12/4/2015 4:48:51 PM

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Air Conditioner Features of your new air conditioner Contents English-4 Safety precautions01epPr aration English-5English-6 For UsingEnglish-7 English-8 Do not place objects or devices under the indoor unitEnglish-9 For CleaningEnglish-10 Smart installChecking before use Operation rangesTechnical Specifications English-11N02asicbctiofun Display Power buttonChecking the name of the parts Main partsChecking the remote controller Remote controller buttonsEnglish-13 Inserting the batteries Remote controller displayLow Battery warning Storing the remote controllerBasic function Press the button to adjust the temperature Press the button to set the desired fan speedEnglish-16 English-17 Adjusting the air flow directionVertical air flow Horizontal air flowYou can adjust the fan speed in Cool/Fan/Heat mode Setting the On/Off timerSetting the On timer Set the timer to press the SET buttonButton  Setting the Off timerSet the timer to English-19Additional options available in mode ModeEnglish-20 Press the SET button to set the 2-Step Cooling function Step cooling functionEnglish-21 Press the Options buttonEnglish-22 Using the Fast functionUsing the Comfort function Set temperature and fan speed cannot be adjustedUsing the Single User function English-23Press the Single user button Using the Auto Clean function Setting the Beep soundEnglish-24 English-25 Cleaning the air conditionerCleaning the outdoor unit heat exchanger Opening the panelOpen the panel and put the Air filter out Cleaning the air filterRemoving the Air filter English-26English-27 Maintaining the air conditionerTroubleshooting Air conditionerEnglish-28 Heard when refrigerant flow movement changes. It is normal Button or disconnect the power plug/switchCheck the Drains have been cleared Regular Maintenance Error is indicatedEnglish-30 General informationIndoor unit Choosing the installation locationInstalling the unit Power supply line, fuse or circuit breakerNoise and vibration Where sulfide gas existsOutdoor Unit English-32When installing more than 1 outdoor unit English-33Top view Side view English-34 AccessoriesAccessories in the indoor unit case Accessories in the outdoor unit caseTools for test operations Fixing the installation plateOptional accessories Tools required for installation General ToolsIf you fix the indoor unit on a gypsum board English-36On a Wall On aEnglish-37 Connecting the assembly cableCable specification Connecting the cable18/24KR  Extend the assembly cable if necessaryEach wire is labeled with the corresponding terminal number English-38Torque English-39Smooth the cut edges Cut off the remaining foam insulationEvacuating the indoor unit Cutting or extending the pipeEnglish-40 English-41 Two hoses are firmly connected, there is no water leakage Drain hose installationEnglish-42 Correct connection Incorrect connection Drain hose PipeCheck for leakage on both side of the drain outlet Change the direction only when it is necessaryChanging direction of the drain hose English-43Drain hole Drain plug Evacuating the connected pipesEnglish-44 Connect a drain hose to the drain plugIf you use a pipe longer than 5 m Adding RefrigerantEnglish-45 Outer TorqueCylinder with siphon English-46English-47 Performing the gas leak testsOutdoor unit installed on the wall by rack Fixing the outdoor unit in placeEnglish-48 English-49 Smart Install modeOff / Blinking / On English-50English-51 Final check and trial operationEnglish-52 Packing and unpacking guideAtio After tube contraction work is completed, wrap it with How to connect your extended power cablesEnglish-53 Apply heat to the contraction tube to contract itEnglish-54 English-55 021-8255 CE Questions or COMMENTS?

AR18KQFHCWKNMG, AR24KRFHCWKNMG, AR24KQFHCWKNMG, AR18KRFHCWKNMG specifications

Samsung has long been a frontrunner in the HVAC (Heating, Ventilation, and Air Conditioning) industry, and its innovative range of split air conditioners, including models AR18KRFHCWKNMG, AR24KQFHCWKNMG, AR24KRFHCWKNMG, and AR18KQFHCWKNMG, exemplifies the brand’s commitment to performance, efficiency, and comfort. These models serve varying room sizes and needs, making them ideal for residential and commercial spaces alike.

One of the standout features across these models is the advanced inverter technology. This technology allows the compressor to operate at variable speeds, adjusting to temperature fluctuations seamlessly. As a result, users benefit from higher energy efficiency and lower electricity bills, while also enjoying a consistent and comfortable indoor climate. The Digital Inverter technology reduces unnecessary energy consumption compared to traditional non-inverter models.

Another key feature of these air conditioners is the triple filtration system. Samsung’s air purifying filters capture dust, allergens, and harmful particles, ensuring a healthier environment. This system includes a reusable and washable filter that promotes ease of maintenance and extends the lifespan of the unit, which is ideal for users who prioritize cleanliness and air quality.

Additionally, noise reduction technology makes these models exceptionally quiet, enhancing user comfort. With operational noise levels kept to a minimum, individuals can enjoy a peaceful atmosphere whether at home or at work, making these units perfect for bedrooms and quiet environments.

These models are also equipped with Smart features, allowing remote control via a smartphone app. Users can monitor and adjust settings from virtually anywhere, adding convenience to their daily lives. The presence of one-touch controls simplifies the user experience, allowing for quick adjustments as needed.

Moreover, the sleek and modern design of the AR18KRFHCWKNMG, AR24KQFHCWKNMG, AR24KRFHCWKNMG, and AR18KQFHCWKNMG ensures that they blend well with contemporary interiors. Their aesthetic appeal, coupled with functional excellence, makes them an attractive addition to any space.

In conclusion, Samsung’s AR18KRFHCWKNMG, AR24KQFHCWKNMG, AR24KRFHCWKNMG, and AR18KQFHCWKNMG air conditioners stand out due to their innovative technologies, energy efficiency, advanced filtration systems, noise reduction capabilities, and smart functionality. These features, along with their stylish designs, make them an excellent choice for anyone looking to enhance their indoor comfort while prioritizing health and efficiency.
Top Page Image Contents