29P~60P(DS990)- NO GB 12/2/04 10:19 Page 40
Setting
the Speaker Mode
Signal outputs and frequency responses from the speakers will automatically be adjusted according to your speaker configuration and whether certain speakers are used or not.
Setting
the Test Tone
Press the Test Tone to check the speaker connections and to adjust the speaker levels.
| 1 | In Stop mode, |
| 2 | Press Cursor | ||||||
|
| button to move to | |||||||||
| press MENU |
| |||||||||
|
| ‘Audio’ and then | |||||||||
| button. |
| |||||||||
|
| press ENTER button. | |||||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OPEN/CLOSE SLEEP DIMMER
DISC SKIP | ZOOM |
| SLOW |
|
|
| MONO/ST |
REPEAT | REMAIN | SUB TITLE | |
TUNER | TAPE |
| AUX |
BAND |
|
|
|
VOLUME | TUNING | ||
PL II |
|
| PL II |
MODE |
|
| EFFECT |
MENU |
|
| INFO |
|
|
| RETURN |
| In Stop mode, |
|
|
| Press Cursor | |||
|
|
|
| button to move to | ||||
| press MENU |
|
|
| ||||
|
|
|
| ‘Audio’ and then | ||||
1 button. |
| 2 | ||||||
| press ENTER button. | |||||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 | Press Cursor button | |
to move to ‘TEST | ||
| ||
| TONE’ and then press | |
| ENTER button. |
•The test tone will be sent to L ➝ C ➝ R ➝ RS ➝ LS ➝ SW in that order.
If the ENTER button is pressed again at this time, the test tone will stop.
In the Speaker
3 Setup, press the ENTER button again.
Press Cursor 
, 
,
, 
buttons to move 4 to the desired
speaker and then press ENTER button.
•For C, LS, and RS, each time the button is pressed, the mode switches alternately as follows: SMALL ➝ NONE.
•For L and R, the mode is set to SMALL.
MUTE |
|
|
| TEST TONE |
|
|
| SOUND EDIT |
|
|
| P.SCAN |
TIMER/CLOCK |
| CANCEL | DIGEST |
TIMER ON/OFF | EZ/VIEW | LOGO | SLIDE MODE |
NTSC/PAL |
|
| |
|
|
|
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
SETUP
SMALL : Select this when using the speakers.
NONE : Select this when no speakers are installed.
Note |
•Depending on PRO LOGIC and STEREO, the speaker mode may vary.
45
When manually testing using the TEST TONE button
Press TEST TONE button.
•Test tone will be produced as follows: When playing a DVD or CD, this will work only in Stop mode.
•Use this function to check that each speaker is correctly connected and that there is no problem.
To end the test tone, press TEST TONE button.
L: Front Speaker (L) | C: Center Speaker | SW: Subwoofer |
R: Front Speaker (R) | LS: Rear Speaker (L) | RS: Rear Speaker (R) |
Start
46